Dvorak SPIDER CROSS LINER Скачать руководство пользователя страница 52

Страница: 52 / 62

Operator’s Manual – Spider CROSS LINER

DRIVE AND STEERING BELTS

INSPECTION

1) Place the mower on a flat and firm surface, press CENTRAL STOP on both the controller and the mower

and remove the key

2) Remove the engine cover and the side covers (4x screw - use a 17 mm socket with an extension).

3) Check the chain tension by applying a slight thumb pressure in the middle of the branch. Deflection should

be within 2 cm.

4) If the tension is insufficient, loosen the belt tensioner pulley nuts and refill.

5) After tensioning, tighten the screws.

6) If any part is damaged or worn, replace it.

TENSIONING

•

DRIVE BELT

Tensioning is carried out with the belt tensioner (Loosen the nut, tension the belt and again tighten the nut.)

•

STEERING CHAIN

Tensioning is carried out with the chain tensioner.

TIP: For better access to belt and chain tensioner on the left, unlock the tank strap and tilt the tank. Carry out
maintenance on the belt and fasten the tank properly back in place. Make sure that no fuel leaks when handling the
tank.

•

TRACTION DRIVE BELT

These are maintenance-free belts, in case of excessive tension, have the belt replaced by an authorized service
center.

EXCHANGE

Damaged and worn chains / belts must be replaced immediately. Have the replacement carried out by an authorized
service center.

HYDRAULIC

PUMP

PULLEYS

HYDRAULIC

PUMP

PULLEYS

HYDRAULIC
PUMP BELT

MOWING

UNIT

SHAFT

MOWING

UNIT

SHAFT

METAL

PLATE

BRAKE

BRZDÍCÍ

PÁS

ŘEMENICE

MOWING

UNIT BELT

MOWING

UNIT BELTS

PULLEY ON

THE

MOTOR

SHAFT

Obrázek

–

Pohonné

prvky

PUL

LEY ON

THE

MOTOR

SHAFT

Figure 20

– Mowing device

Содержание SPIDER CROSS LINER































































Результаты поиска

Содержание SPIDER CROSS LINER

Отзывы:

Похожие инструкции для SPIDER CROSS LINER

Бренды по названию

Популярные бренды

Dvorak SPIDER CROSS LINER, Руководство оператора

Результаты поиска

Содержание SPIDER CROSS LINER

Отзывы:

Похожие инструкции для SPIDER CROSS LINER

Бренды по названию

Популярные бренды