Dutchess JN Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 39

Dutchess JN Скачать руководство пользователя страница 17

TROUBLESHOOTING

Problem:

Solution:

Partial Rounding of Dough Balls

1. Pocket height set too high:

-Readjust pocket height, see Adjustments, Pg. 5.

2. Rounding time too short:

-Increase rounding time.

3. Pallet is oily or floured:

-Wash and dry pallet.

4. Drive Belts slipping:

-Adjust or replace belts, see Adjustments, Item 2, pg. 5.

Flour Pocket in Dough Ball:

-Use less flour on top of dough.

Imperfection of Dough Ball:

-Usually caused by over, or under rounding.

(Normal rounding time: 5 - 15 seconds.)

-Pocket height set too high or too low.

(Raise or lower as needed.)

Rounding Action Will Not Stop:

Rounding lever not returning to
idle position:

-Lubricate linkage.
-Check slide springs.

Crank Plate will Not Center:

-Adjust drive slide centering, see adjustment pg. 5.

1. Broken slide spring:

-Replace spring.

2. Slides/drive slide sticking:

-Clean slides, lubricate.

WARNING!

The power switch is to be in the OFF position, and

the machine disconnected from the power source,

before servicing or cleaning.

12

«
...
15
16
17
18
19
...
»

Содержание JN








































Отзывы:

Нет отзывов