manualshive.com logo in svg

Duratrax Delphi Indy Car, Руководство по сборке и эксплуатации

Поделиться
Скачать
Duratrax Delphi Indy Car Скачать руководство пользователя страница 6

6

❏

1. Remove the upper plate by removing the two body clips

in the front and lifting the front of the upper plate up out of the
way. Note: To completely remove the upper plate you
must first detach the rear shock from the upper plate.

❏

2. Using a pair of sharp cutters or a hobby knife remove the

servo mounting tabs on both ends of the servo as shown
above. Make sure the area where the mounting tabs were
located is flush with the case when you are done. This will
provide a good contact surface for the servo to mount.

❏

3. Install a piece of included double-sided tape to the inside

of the servo mount and a piece to the chassis as shown.

❏

4. Install the servo onto the chassis, securing it in place

with the double-sided tape. Note: The servo needs to be
mounted so that the output shaft is in the upper position
as shown.

❏

5. Locate the two servo saver parts (69) and (70 FUT, AIR,

HTEC, or MUL, depending on your servo brand) and install
them onto the pre-mounted servo saver part (68). Install this

STEERING SERVO INSTALLATION

Содержание Delphi Indy Car

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды