Duratrax Delphi Indy Car Скачать руководство пользователя страница 1

Warranty

DuraTrax

®

will warranty this kit for 90 days after the purchase date from defects in materials or workmanship. DuraTrax

will either repair or replace, at no charge, the incorrectly made part.

Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase
and we must see it before we can honor the warranty. Further, DuraTrax reserves the right to change or modify this
warranty without notice.

To return your Delphi Indy car for repairs covered under warranty you should send your vehicle to:

Hobby Services

1610 Interstate Drive

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F

E-mail:

[email protected]

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to
return this kit immediately in new and unused condition to the place of purchase.

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS
AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

v1.0 © Copyright 2002

DTXZ1100 For Kit DTXC0012/DTXD12**

ASSEMBLY AND OPERATION MANUAL

Weight: 1lb 14oz
Length: 17.25" [435mm]
Width: 8" [205mm]
Height: 4.5" [115mm]
Wheelbase: 10.5" [265mm]
Motor: 20 Turn Photon Speed
Radio: 2 channel surface frequency

Technical Support Information

For technical assistance, contact:

Duratrax Product Support

1610 Interstate Drive

Champaign, IL 61822

(217) 398-8970, Ext. 2

[email protected]

®

Содержание Delphi Indy Car

















Отзывы: