manualshive.com logo in svg

DURAG D-FL 200, Руководство пользователя

Поделиться
Скачать
DURAG D-FL 200 Скачать руководство пользователя страница 24

D-FL 200 / Rev. 6 

21 

______________________________________________________________________________________________________ 

  Industrie Elektronik GmbH & Co KG

 

default 332 m/s (corr. to 1089 ft/s) 

R32 

calibration time 

calibration interval (0-720h), disabled=0, 

default 24h 

R33 

normal/reverse 

inverse mode for the velocity measurement (0=normal 
direction, 1= inverse), default 0 

 

 

8.1. Key Functions  

 

The keys have the following functions: 

 

Key 

 

For switching to the “

Input” (storing) mode. 

The LED on the "STO"-key is illuminated when in this mode. 

Key 

 

For switching to the “

Display” mode. 

The LED on the "MOD"-key is illuminated. 

Key 

 

For counting up when in the “

Input” mode, and for switching the display when 

in the “

Display” mode.  The LED in the “MOD” key is illuminated.  

Key 

 

For counting down when in the “

Input” mode, and for switching back the 

display when in the “

Display” mode.  The LED in the “MOD”-key is illuminated.  

 

8.2. Storing / Entering Parameters by using the Keys 

• 

Pressing the “MOD”-key switches from the 'Measuring'-mode to the 'Display'-mode. The “MOD” 
LED is illuminated. 

• 

The “+“-key causes that the parameters will be displayed one after the other, according to the 
second table below 

Fig.19. The corresponding parameter appears in the display. 

• 

Pressing the “STO”-key switches the system into the “Input” mode. The “STO” LED is illuminated. 

• 

The “+“ and “-“ can be used to change the value in the display. The longer these keys are 
pressed, the more quickly the value is changed. 

• 

If the “STO”-key is pressed again, the new value is stored and the system switches back to the 
“Display” mode.  The “STO” LED is extinguished. 

• 

By pressing the “MOD”-key the system switches back from the “Display” mode to the “Measuring” 
mode. The “MOD” LED is extinguished, and the current measured value is shown on the display. 

If the system is switched back from the “Input” mode to the “Measuring” mode using the “MOD”-
key before the new values are stored, they will not be saved. 

8.3. Storing / Entering Parameters via the RS232 Interface 

Parameters may also be entered using the serial interface of a PC or Notebook. The D_FL_COM 
parameter program can run on Windows 3.1x and Windows 95/98. The detailed description how to use 
it you find in section 

10.  PC-Parameterisation of the D-FL 200COM page 25. 

 

Содержание D-FL 200















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды