DURAG D-FL 200 Скачать руководство пользователя страница 23

Страница: 23 / 46

D-FL 200 / Rev. 6

______________________________________________________________________________________________________

Industrie Elektronik GmbH & Co KG

R12

zero_tmperature_in

Beginning of measuring range for temperature sensor (4
mA) (0-800°C) (corr. to 32-1472°F)

R13

span_tmperature_in

End of measuring range for temperature sensor (20 mA) (0-
800°C) (corr. to 32-1472°F)

R14

zero_pressure_in

Beginning of measuring range for absolute pressure sensor
(4 mA) (0-1500hPa)

R15

span_pressure_in

End of measuring range for absolute pressure sensor (20
mA) (0-1500hPa)

R16

const_tmp

constant temperature (0-800°C) (corr. to 32-1472°F)

R17

const_p

constant absolute pressure (0-1500hPa),

default 1013

Parameter code_2

Release code for internal parameterisation,

only for internal

use at Durag factory, code = 200

R22

frequency

Drive frequency for ultrasonic sensor / evaluation algorithm
(10-100kHz),

MK1=50kHz, MK2=41kHz, MK3=30kHz

R23 amplitude

min.

Minimum signal amplitude, values below this limit are not
evaluated. If this appears 30 seconds in a row, the error
detection is launched (E16-E19),

(0-2000), default 350

R24

amplifier target

Set point for the automatic gain control,

constant 1900

R25

amplification f..

Amplification factor/ manual/ automatic; values

between 1 and 512 will set the variable amplifier to a fixed
amplification, values greater than 512 enable the automatic
gain control (0-1000),

default 600

R26

assessment level

Assessment level, used for searching of the trigger point,
constant 10

input temperature

mA input for temperature

input pressure

mA input for absolute pressure

R27

error detection

Error detection system, enabled=1, disabled=0; single error
evaluations can be disabled by setting the value or the sum
of values: 2

E12-E15; 4

E16-E19; 8

E20-E23; 16

E24-

E27; 32

E28-E31; 64

E32-E33

R28

zero suppress

Zero suppress of gas flow velocity (0-3m/s) (10ft)

R29

sensor offset

Sensor offset , (0-600mm) (corr. to 23,6in),

default 0

R30

noise limit

noise limit, signals with a higher noise component are not
evaluated. If this appears longer than 30 seconds in a row,
the error detection is launched (E24-E27) (0-2000), default
450

R31

ultras. speed NT

Ultrasonic speed at 0°C (100-500m/s),

Содержание D-FL 200















































Результаты поиска

Содержание D-FL 200

Отзывы:

Бренды по названию

Популярные бренды

DURAG D-FL 200, Руководство пользователя

Результаты поиска

Содержание D-FL 200

Отзывы:

Бренды по названию

Популярные бренды