manualshive.com logo in svg

Durafly Curtiss P-40N, Инструкция по эксплуатации

Поделиться
Скачать
Durafly Curtiss P-40N Скачать руководство пользователя страница 20

SPARE PARTS LISTING

Prop shaft

Part No.: 9306000203-0 

Decal sets

Part No.: 9306000201-0

Fuselage

Part No.: 9306000190-0

Horizontal tail

Part No.: 9306000192-0

Spinner set

Part No.: 9306000196-0

Propeller set

Part No.: 9306000193-0

Scale plastic parts

Part No.: 9306000194-0

Bomb

Part No.: 9306000195-0

Control/mounting 

accessories

Part No.: 9306000200-0

Main wing inc bomb servo

Part No.: 9306000191-0

Motor inc shaft & X mount

Part No.: 9306000202-0

Tail wheel assembly

Part No.: 9306000198-0

Retracts/main gear

Part No.: 9306000199-0

Battery hatch

Part No.: 9306000197-0

Applying the supplied decals will take you longer than assembling the model. This is because great 

care must be taken when doing so. The decals are vinyl type and so need to be applied in a certain 

way. Please follow carefully the guidelines below to achieve the best possible finish on your P-40N.
1. Study the scheme reference sheet carefully and understand fully where each decal should be applied.
2. DO NOT cut to the edge of each decal. Instead leave a 10mm edge around it. These decal use a 

clear front cover/film that is used to remove the decal from the paper backing.

3. Once you have cut out your decal rub the surface of the clear protective film to ensure the decal 

sticks it. This will ensure all of the decal is lifted off the backing paper

17

4. Position the decals carefully on the model according to the decal reference sheet then gently rub 

(using a dry cloth) the decal in place rubbing from the center of the decal out to avoid wrinkles and 

air bubbles.

5. If you do have some air bubbles under the decal, use the tip of a sharp blade to make a small hole 

in the bubble then rub over it again to push the air out.

6. Once the decal is firmly rubbed down and any air bubbles removed, you can slowly remove the front 

clear protective film. DO NOT pull this clear film upwards to remove it, instead pull the film slowly off 

to the side. This will ensure the decal doesn’t lift up from the surface of the model when you remove 

the clear film.

7. Very gently rub the decal again with a cloth now that the clear film is removed to ensure all edges 

are firmly stuck down.

8. Finally the use of a covering iron is STRONGLY recommended to seal the decals to the painted 

foam surface and prevent them from lift at the edges over time. Set the iron to a low temperature 

and gently run the iron lightly over the surface of the decal as illustrated below. Use of a cloth to 

cover the head of the iron is recommended to help prevent damage to the foam and the decal. A 

house hold iron can be used if no covering iron is available.

DECAL APPLICATION GUIDELINES

Содержание Curtiss P-40N









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды