background image

-15-

SOLUTION
•  DO NOT light the burner.  Extinguish any open 

flame near the spill.  Wipe up the spill, and wait 

several minutes for the residue to evaporate.  

If you see no additional fuel on the ground, 

you may light the burner.  If you see additional 

fuel on the ground, you might have a leak.  DO 

NOT use this appliance if it leaks fuel.

•  The appliance may not be level.  Check 

to make sure the appliance is level, and 

shim under the grate legs or rear support, if 

necessary.  Shim only with metal washers or 

other non-flammable objects.

•  A small piece of foil that covers the 

opening of the illuma-fuel

®

 canister might 

be obstructing the piercer tube.  Open the 

fuel canister door on the left side of the 

appliance.  Gently wiggle the fuel canister 

left to right and front to rear on the fuel 

canister tray to enlarge the opening in the 

foil.  DO NOT lift the illuma-fuel canister from 

the tray, as this could cause a fuel spill.

•  The tubes connecting the burner to the fuel 

reservoir might be clogged.  Starting at the 

tube opening in the bottom of the burner, run 

a thin, flexible wire through the length of the 

tube to remove the obstruction.

•  The battery in the igniter may be dead.  

Replace it with a new battery

•  The sparker tip may be out of position.  The 

tip of the sparker should be about ¼” above 

the level of the sparking point.  Carefully 

bend the wire so that the tip of the sparker 

wire is in this position

•  The fuel is cold or the appliance is cold.  

Use a long match or a long butane lighter to 

ignite the fuel.

•  If the fuel is hot, the fuel vapors stop oxygen 

from being in the vicinity of the spark.  Thus 

not allowing the fuel to ignite.  Wait until the 

fuel is cool or relight the appliance using a 

long match or a long nosed butane igniter. 

PROBLEM
1. You see fuel on the ground near the 

appliance.

2. You do not see fuel in the burner prior to 

lighting the appliance and after installing a 

canister.

3. You push the igniter button but the appliance 

does not light.

XII. TROUBLESHOOTING

Use the following guide to solve any problems you might encounter in operating this appliance.

Содержание illuma 64000



















Отзывы: