background image

01/09/14

Direct Vent Gas Fireplace

FOR YOUR SAFETY
What to do if you smell gas:

 

Do not try to light any 

 appliance
  Do not touch any electri-

cal switch: do not use any 
phone in your building.

  Immediately call your gas 

supplier from a neighbour's 
phone. Follow the gas sup-
plier's instructions.

  If you  cannot reach your 

gas supplier, call the fi re 
department.

WARNING:  
Improper installation, adjustment, altera-
tion, service or maintenance can cause 
injury or property damage. Refer to this 
manual. For assistance or additional in-
formation consult an authorized installer, 
service agency or the gas supplier.

FOR YOUR SAFETY
Do not store or use gasoline or other fl am-
mable vapours and liquids in the vicinity of 
this or any other appliance.

Installation and service must be performed 
by an authorized installer, service agency or 
the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS 

FOR FUTURE REFERENCE

Owners &

Installation

 Man

ual

LISTINGS AND CODE APPROVALS

These gas appliances have been tested 
in accordance with AS4553-2000, NZS 
5262 and have been certifi ed by the 
Australian Gas Association for instal-
lation and operation as described in 
these Installation and Operating In-
structions.

Your unit should be serviced annually 
by an authorised service person.

918-647a

Models: HG35-NG1
 HG35-LPG1

Summary of Contents for HG35-NG1









































Reviews: