background image

Isokern

®

 BVETTO

TM

 B-Vent 

Gas Fireplaces and Chimney System

Installation, Operation, Maintenance and Owner’s Manual

Isokern BVETTO Models 80B36 & 80B46

A PRODUCT OF EARTHCORE

®

 INDUSTRIES, LLC

IMPORTANT: 

This manual contains assembly rules, installation steps and guidelines, and use and maintenance in-

structions for Isokern B-VENT gas appliances (BVETTO). This manual must become the property of and be reviewed 
by all current and future users of this product. It is the responsibility of the distributor, general contractor and the 
installer of this product that the instructions in this manual are followed exactly and, further that the allowed gas log 
appliance used in this product be installed in strict accordance with the gas log manufacturer’s listing and explicit 
installation and operation instructions.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference

Be Sure to Read Entire Manual Before Beginning Construction.

Contents of this manual may change without prior notification.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warning exactly could  
result in serious injury, death, or property damage.

— Do not store or use gasoline or other  
  flammable vapors and liquids in the vicinity  
  of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS
  • Do not try to light any appliance.
  • Leave the building immediately.
  • Do not touch any electrical switch; do not
    use any phone in your building.
  • Immediately call your gas supplier from a  
    neighbor’s phone. Follow the gas supplier’s
   instructions.
  • If you cannot reach your gas supplier, call
    the fire department.

— Installation and service must be performed
  by a qualified installer, service agency or the
  gas supplier.

Issued: August 2017

Revision: 005

©2017 Earthcore Industries, LLC

THESE FIREPLACES ARE DESIGNED for USE with:

PROPANE (LP) or NATURAL GAS (NG), ONLY

THIS MANUAL CAN ONLY BE REPRODUCED IN ITS ENTIRETY

Do not install the BVETTO B-Vent Gas Fireplace in a 
manufactured home or mobile home or recreational 
vehicle.

PFS Report No. 09-79

SAP No. 506022-03

USA: ANSI Z21.50 - 2014

Canadian: CSA 2.22- 2014

—  

This appliance complies with National Safety and  

 

is tested and listed to ANSI Z21.50 - 2014 as  

 

vented gas fireplaces.

— 

Installation must conform to local codes. Check

 

local codes prior to installation. In the absence of  

  local codes, installation must conform with 

 

 

current National Fuel Gas Code, ANSI Z223.1.

Summary of Contents for BVETTO 36 inch













































Reviews: