background image

Page 1

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

DIRECT VENT ZERO CLEARANCE

GAS FIREPLACE HEATER

MODEL SERIES:

MILLIVOLT (MV)

ADVCX(36,42)FP30(N,P)-2

INTERMITTENT PILOT (IPI)

ADVCX(36,42)FP70(N,P)-2

MH30033

INSTALLER:  Leave this manual with the appliance.

CONSUMER:  Retain this manual for future reference.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only) or mobile home, where not prohibited by 

state or local codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless 

a certified kit is used.

 WARNING

If the information in these instructions are 

not  followed  exactly,  a  fire  or  explosion 

may result causing property damage, per-

sonal injury or loss of life.

— Do not store or use gasoline or other 

flammable  vapors  and  liquids  in  the  vi

-

cinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do 

not use any phone in your building.

  •  Immediately call your gas supplier 

from  a  neighbor’s  phone.  Follow  the 

gas supplier’s instructions.

  •  If you cannot reach your gas supplier, 

call the fire department.

—  Installation  and  service  must  be  per

-

formed  by  a  qualified  installer,  service 

agency or the gas supplier.

 

WARNING

If not installed, operated and maintained in ac-

cordance with the manufacturer’s instructions, 

this product could expose you to substances in 

fuel or from fuel combustion which can cause 

death or serious illness.

GAS-FIRED

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.

Note:

 Barrier required, but may be sold separately.

Summary of Contents for Intermittent Pilot ADVCX36FP70N-2





































































Reviews: