For parts or assistance, call Duracraft Customer Service at
1-888-749-5759
Specifications and Safety
2
DESCRIPTION
This Submersible Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-type
power cord. Shaded-pole motor is oil filled and sealed
for cooler running. Sleeve bearings on motor shaft never
need lubrication. Automatic reset thermal protection. Not
designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge: ........................1-1/4" FNPT / 1-1/2" MNPT
NOTICE:
Do not reduce size of discharge pipe or
hose below 1-1/4” diameter. If discharge is too
small, pump will overheat and fail prematurely.
Pump water only with this pump.
NOTICE:
This unit is not designed as a waterfall or foun-
tain pump, or for applications involving salt water or
brine! Use with waterfalls, fountains, salt water or brine
will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
PERFORMANCE
ELECTRICAL & SWITCH SPECIFICATIONS
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump’s capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from func-
tioning normally. To prevent possible water damage
due to flooding, consult your retailer about a sec-
ondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the “Troubleshooting
Chart” in this manual for information about common
sump pump problems and remedies. For more infor-
mation, see your retailer, call Duracraft customer
service at 1-888-749-5759 or visit our website at
www.duracrafttools.com.
1. Know the pump application, limitations, and
potential hazards.
2.
The oil-filled motor was not designed for use in
water containing fish. Do not use this pump in
water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before servic-
ing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
7. Check hoses for weak or worn condition before
each use, making certain that all connections are
secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
9. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working
with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
11. When wiring an electrically driven pump, follow
all electrical and safety codes that apply.
12.
This equipment is only for use on 115 volt (sin-
gle phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type
plug.
GPH (LPH) AT TOTAL FEET (M) OF LIFT
Motor
5
10
15
Series
HP
(1.5m)
(3m)
(4.6m)
CAPACITY GALLONS(L)/HOUR
DCMKP33T
1/3
2760
2160
1410
20 Ft.
(10 448)
(8 176)
(5 337)
(6.1M)
DCMKP50T
1/2
3200
2700
2000
24 Ft.
(12 113) (10 220)
(7 571)
(7.3M)
No flow
at height
shown
below
Individual
Motor
Branch
*Switch Setting
Motor Full Load
Circuit
in inches (mm)
Series
HP
Amps
Req.(Amps)
On
Off
DCMKP33T
1/3
5.5
15
13"(330)
6"(152)
DCMKP50T
1/2
9.0
15
13"(330)
6"(152)
Содержание DCMKP33T
Страница 20: ......