DUERR-NDT CR 43 NDT Скачать руководство пользователя

Страница: 29 / 36

2013/10/21

9000-608-21/30

Problem

Possible cause

Solution

7. Cassette is not

drawn into the
cassette slide

• Cassette not properly engaged

• Position the cassette correctly

• Cassette not pushed in correctly

• Position the cassette correctly

• CR 43 is not ready

• Activate CR 43

8. X-ray exposure

does not appear
on the screen after
the scanning

• Image data on the image plate of

the cassette were erased, eg by
natural or scattered X-ray radia-
tion

• Image data on the image plate

must be read out as quickly as
possible after removal

• Problem with the hardware

• Inform your service technician

• X-ray device is faulty

• Inform your service technician

• No image information on the im-

age plate of the cassette

• Expose the image plate

9. X-ray too dark/

light

• Wrong brightness/contrast setting

in the software

• Set the brightness of the X-ray

image with the software

10. X-ray unclear

• X-ray dose too low

• Check the X-ray parameters

11. Ghosts and shad-

ows on the X-ray
exposure

• Image data on the image plate in

the cassette were not sufficiently
erased

• Erase the image plate of the cas-

sette again

12. CR 43 does not

appear in the
selection list in
CRConfig

• Appliance is connected behind a

network router

• Configure the IP address at the

CR 43 without an intermediate
network router

• Connect the network router again
• Enter the IP address manually in

CRConfig and register the appli-
ance

13. Image appears

shadowy on the
scan window
Software cannot
combine data to
make a complete
image

• The X-ray dosis on the image

plate was insufficient

• Increase the X-ray dose

• The amplification is set too low

(HV value)

• Increase amplification (HV value)

• The selected scan mode is not

suitable

• Select suitable scan mode

• The setting for the threshold value

is too high

• Reduce setting

14. When starting

the X-ray module
in D-Tect, a fault
message appears

• CR 43 is conflicting with another

device

• In "CRConfig", set the CR 43 or

the like to "Demo without Scan-
ner"

Содержание CR 43 NDT





































Результаты поиска

Содержание CR 43 NDT

Отзывы:

Похожие инструкции для CR 43 NDT

Бренды по названию

Популярные бренды

DUERR-NDT CR 43 NDT, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CR 43 NDT

Отзывы:

Похожие инструкции для CR 43 NDT

Бренды по названию

Популярные бренды