Duerkopp Adler 1183i-7 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

Duerkopp Adler 1183i-7 Скачать руководство пользователя страница 18

15

3.

6 F

eeding

m

echanis

m

of

the

to

p

roller

3.

6

.

1

Descri

p

tion

The starting movement for the drive of the top roller feeder is

the bottom feeding shaft. From this shaft, the movement is

transmitted by the indented belt (1) onto the top feeding shaft

(2). A component part of the transmission by indented belt is

the pulley (3), the tensioning roller (4), the roller (5) and the

pulley (6). Starting from the shaft (2), the movement is further

transmitted through the wheels (7 and 8) ontothe articulated

shaft (9). From this articulated shaft, the movement is

transmitted by a cone transmission, situated in the holder

(10), onto the feeder wheel (11). The shaft of the wheel (8) is

mounted in the screw (12) on bearings. The articulated shaft

(9) contains two joints (15) and a telescopic part (16). Both

these elements secure the lifting and the tilting of the top

roller.

3.

6

.2 Side

setting

of

the

indented

lower

p

ulley

The pulley must be set up in such a way that the belt passes

through the centre of the passing hole in the bedplate. The

setting operation is to be done as follows:

Caution!

Danger

of

injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Loosen the screws (1) of the pulley (2).

- Loosen the screw (3) of the tensioning roller (4)

- Set the pulley (2) in such a way that the belt (5) passes

through the centre of the passing hole in the bedplate (6).

- Tighten the screws (1).

- Set the tensioning roller (4) axially in such a way that the

belt (5) is set at the middle of the tensioning roller (4).

- Set the tensioning roller (see par. 3.6.4).

- Tighten up the screw (3) of the tensioning roller (4).

3.

6

.3 Side

setting

of

the

indented

u

pp

er

p

ulley

The pulley is to be set in such a way that the indented belt is

not crossed and the pulleys are in line. The setting thereof is

to be done as follows:

Caution!

Danger

of

injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Loosen the screws (1) of the pulley (2).

- Set the pulley (2) in such a way that the distance of 5 mm

is attained in accordance with the illustration.

- Tighten the screws (1).

$

#

"

!

#

'

$

#

&

!

"

%

#

"

!

#

$

«
...
16
17
18
19
20
...
»

Содержание 1183i-7




































Отзывы:

Нет отзывов