Duerkopp Adler 1183i-7 Скачать руководство пользователя страница 11

Страница: 11 / 35

3.4 Thread tensioners and limiter

3.4.1 Description

The main tensioners (1) serves for creating the tension of the

thread when tightening the stitch. The auxiliary tensioner (2)

reduces the risk of pulling out of the thread after the thread

trimming when removing the sewn material, when the thread

is passed through this material and when the main tensioner

is relieved.

The main tensioner is relieved by the mechanism

controlled by the shaft of the presser bar lifting (3) holding

the lever (4) with a pulley. The motion is then transmitted by

the lever (5) and the tie rod (6) on the thread tensioner plate

(7) whose displacement (motion) relieves the thread tensioner

springs (8). In machines provided with a thread trimming

device, the main tensioners (1) are relieved as well upon the

switching on of the electromagnet (10) whose electromagnetic

field will attract the thread tensioner plate (7).

The mechanism

of the adapting spring (12) maintains the upper thread in its

tensioned state when passing through the hook

and when

entering the needle into the sewn material

. The thread limiter

(13) limits the length of the thread fed by the take-up lever

when moving from the upper to the bottom dead centre to get

a controlled passing of the thread through the hook.

The

auxiliary guide (14) maintains the upper thread in front of the

needle in a tensioned condition and helps against pulling the

thread from the needle after thread trimming.

3.4.2 Setting the tension of the main and auxiliary

tensioners

The tension of the main thread tensioners is regulated by

means of the nuts (1).

The force of tensioning the thread is

measured by the dynamometer (2) as it is shown on the

illustration.

The size of this force differs according to the

category, and its orientation value is indicated in the par. 11.2.

The tension of the auxiliary tensioner is regulated using the

nut (3). It should be the least possible, but sufficient for

unthreading the thread from the sewn material when removing

the sewn material from the pressing element without leaving

the tensioner.

3.4.3 Setting the tensioning mechanisms

of the main tensioners

In the rest position of the tensioners, when pushing the plate

of the tensioners on the spot A 3.4.1, this plate must have

the socalled dead travel of about 0,5 mm. At this lifting, the

tension discs of the tensioners must not be relieved. This can

be attained by a suitable shaping of the relieving disc of the

tensioners - this has been set up in the manufacturing factory.

In the maximum opened position of the tensioners, the plate

of the tensioners, when pushing it at the spot A 3.4.1, must

still have the minimum lifting. This can be attained when axially

shifting the lever (3) with the roller (5) on the shaft (4).

The disengagement of the main tensioners must be

coordinated with the top roller lift. To achieve this, turn the

lever (3) with the roller (5) on the shaft (4). The movement of

the roller (5) on the slanting surface (6) of the lever (7)

disengages the tensioners. In this way, also a lag of the upper

thread tension disengagement after the top roller lift can be

obtained.

Caution ! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

Remove the rear cover with the top roller lift magnet.

- Loosen the screws (1) and (2) of the lever (3).

A
7

3 2 5

0,1

Содержание 1183i-7




































Результаты поиска

Содержание 1183i-7

Отзывы:

Duerkopp Adler 1183i-7, Инструкция по эксплуатации, Страница: 11 / 35

Результаты поиска

Содержание 1183i-7

Отзывы: