Duerkopp Adler 1183i-7 Скачать руководство пользователя страница 12

Страница: 12 / 35

- In the rest state of the machine (with not relieved tensioner

discs) set the lever (3) in turning it slightly on the shaft (4)

to a position in which the roller (5) of the lever (3) is in

contact with the slanting surface (6) of the lever (7) and is

about 0.1 mm distant from the flat surface (8) of the lever.

- At the maximum lift of the top roller, the roller (5) moves on

the flat surface (9) of the lever (7); in this condition, there

must be a minimal play at the tensioner plate lift (when

pushing qat the spot A (3.4.1), the plate must still have a

minimum lifting - between the roller (5) and the surface (9)

there is a minimum clearance). Retighten the screws (1) and

(2), check the play, and correct it in case of need.

3.4.4 Setting the adapting spring

The mechanism of the adapting spring is in the machine arm

set by the pin (1) and fixed by the screw (2). The axial

adjustment shall ensure that the surfaces of the parts (3) and

(4) are aligned (the threaded thread must in no place break on

edges). The initial position of the adapting spring (5) shall

ensure that B = 1 to 1.5 mm (see the Figure).

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

Loosen the screw (2) and take the mechanism out of the

machine arm.

- Turning the body (6) relative to the pin (1), set the required

initial position of the adapting spring /the screw (7) has

been set at the producer´s so as to permit the turning

movement of the body (6) the screw must not be fully

tightened/.

- During the installation of the mechanism into the machine

arm take care of the axial adjustment of the mechanism.

- Retighten the screw (2) and check the adjustment.

- Loosen the nut (8) of the mechanism, insert a screwdriver

into the notch of the screw (9) and set the required value of

the adapting spring. By turning the screw clockwise you

increase the spring force, and vice versa.

- Retighten the nut (8) and check the function of the adapting

spring.

3.4.5 Setting the thread limiter

The thread limiter is to be set in such a way that, when sewing

and passing the thread through the most distant point of the

hook, the spring (2) shifts by about 1/4 to 1/2 length of its

total length. This means that the thicker will be the sewn

material and the longer will be the stitch length, the more will

be the limiter shifted in the sense of the arrow and inversely.

Under standard sewing conditions, the thread limiter is set in

its tested positions depending on the sewing category in

accordance with the chapter 11.

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Tighten the screw (3).

Set the thread limiter (1) so as to ensure a minimum motion

of the adapting spring (2) when the thread passes around

the bottom of the hook.

- Tighten the screw (3).

Содержание 1183i-7




































Результаты поиска

Содержание 1183i-7

Отзывы:

Duerkopp Adler 1183i-7, Инструкция по эксплуатации, Страница: 12 / 35

Результаты поиска

Содержание 1183i-7

Отзывы: