Duerkopp Adler 1183i-7 Скачать руководство пользователя страница 14

Страница: 14 / 35

d a

stitc

h l

istri

ution

(

fine

)

When setting the maximum length of the stitch, the forward

and the rearward stitch length must be equal with the

maximum error of ± 5 %. This setting can be done only after

having set the needle bar holder in the direction of sewing

(par. 3.2.6) and the wheel feed (par. 3.5.3.1.2).

ution

! Da

switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Set the maximum stitch length .

- Place a suitable material under the presser foot and mark

therein the forward and the rearward stitch length.

- With an unequal length of the stitch, proceed to the

correction of setting by turning the screws (2 and 3). When

tightening the screw (3), the forward length of the stitch is

shortened and inversely. When tightening the screw (2), the

forward stitch length is lenghtened.

Each time first loosen one screw and then retighten the

other one.

Settin

contro

l k

(

inc

stitc

h l

tion

)

The control knob (1) is to be set up in such a way that, when

turning it in counterclockwise sense up to the stop, the

maximum stitch length valid for the given sewing category is

attained (cat. cat 2 and 3: 5 mm). The scale of the control knob

is to be oriented in such a position, so that the scale end

corresponds to the maximum stitch length.

ution

! Da

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Screw in the screw of the control knob in such a way, that

the spherical surface of the screw (3) bears on the seat of

the cam (4).

- Loosen the screw (5) and turn the control knob in the

clockwise direction, until the pin (6) of the knob (1) bears

on the pin (7). Tighten firmly the screws (5).

- Turn the knob in the counterclockwise direction up to the

stop, when the pin (6) of the knob (1) bears on the pin (7).

- In a sewing test check up the length of the stitch, if this

corresponds to the maximum stitch length valid for the given

sewing category.

- If the stitch is longer, loosen then the screws (5) and turn

the knob in the clockwise direction and inversely. Tighten

firmly the screws (5).

- Insert a screwdriver into the hole (8) of the scale (2) and

adjust the scale in such a way that the maximum length on

the scale is against the marking of the stitch length on the

machine arm.

Содержание 1183i-7




































Результаты поиска

Содержание 1183i-7

Отзывы:

Duerkopp Adler 1183i-7, Инструкция по эксплуатации, Страница: 14 / 35

Результаты поиска

Содержание 1183i-7

Отзывы: