manualshive.com logo in svg

Du Pont SORVALL RT6000B, Руководство по эксплуатации

Поделиться
Скачать
Du Pont SORVALL RT6000B Скачать руководство пользователя страница 24

Maintenance

SORVALL

®

 

Centrifuges

4-6

2.

Send item(s) with the RSO# clearly marked on the outside of packaging to the address
obtained from your Du Pont representative.

NOTE

United States federal regulations require that parts and instruments 

must

be decontaminated before being transported.

If a centrifuge or rotor to be serviced does not have a Decontamination Information
Certificate attached and, in Du Pont's opinion presents a potential radioactive or biological
hazard, the Du Pont representative will not service the equipment until proper decontami-
nation and certification is complete. If Du Pont receive a centrifuge or rotor at its Service
facilities which, in its opinion, is a radioactive or biological hazard, the sender will be
contacted for instructions as to disposition of the equipment. Disposition costs will be
borne by the sender.

Decontamination Information Certificates are included with these instructions. Addi-
tional certificates are available from your local Account Representative or Field Service
Engineer. In the event  these certificates are not available, a written statement certifying
that the unit has been properly decontaminated and outlining the procedures used will
be acceptable.

NOTE

The Field Service Engineer will note on the Customer Service Repair Report
if decontamination was required and, if so, what the contaminant was and
what procedure was used. If no decontamination was required, it will be so
stated.

Содержание SORVALL RT6000B





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды