manualshive.com logo in svg

Du Pont SORVALL RT6000B, Руководство по эксплуатации

Поделиться
Скачать
Du Pont SORVALL RT6000B Скачать руководство пользователя страница 10

SORVALL

®

 

Centrifuges

Installation

2-1

Chapter 2

INSTALLATION

This chapter contains instructions to prepare your SORVALL

®

 RT6000B and T6000B for

operation.

Inspection

When you receive your centrifuge, carefully inspect it for any signs of shipping damage.
If you find damage, report it immediately to the transportation company and file a damage
claim, then notify Du Pont.

Check the parts received with the centrifuge against the shipping list; if any parts are
missing, contact Du Pont (see back cover).

WARNING

The RT6000B weighs 187 lbs. and the T6000B weighs 160 lbs.  Refer to
the unpacking instructions for proper care when lifting and installing the
centrifuge.  Failure to use proper lifting techniques can result in possible
damage to the centrifuge and/or personal injury.

CAUTION

Do not lift the centrifuge by the front panel or by the lid.  To do so can result
in damage to these parts.

Do not place the RT6000B on its side; any position other than upright can
cause compressor contamination.

Electrical Requirements

The centrifuge has specific power requirements and must be connected to the correct
supply for proper performance.  The nameplate on the back of the cabinet specifies one
of the following:

105-125 Vac, 60 Hz, single phase, 15 amps*

210-230 Vac, 50 Hz, single phase, 8 amps*

105-125 Vac, 60 Hz, single phase, 8 amps

210-230 Vac, 50 Hz, single phase, 4 amps

The current draw during acceleration in the T6000B could peak to 15 amps for 60 Hz
centrifuges and 8 amps for 50 Hz centrifuges.  Therefore, if the main power source is

*CSA and UL Certified

RT6000B:

T6000B:

Содержание SORVALL RT6000B





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды