manualshive.com logo in svg

DT SWISS SPLINE WHEEL, Техническое руководство

Поделиться
Скачать
DT SWISS SPLINE WHEEL Скачать руководство пользователя страница 13

SPLINE Wheels - Technical Manual

13

3.  HUB MAINTENANCE

This chapter describes a small hub service. This includes:

•  End caps: Disassembling, cleaning, greasing and assembling
•  Freewheel body: Disassembling, cleaning, greasing and assembling
•  Freewheel system: Cleaning and degreasing.

The description of a full hub service can be found in the technical manual of the respective hubs at  

dtswiss.com.

3.1  SERVICE INTERVALS

The following regular maintenance and care work is recommended by DT Swiss:

Task

Interval

Small Service

•  Under normal operating conditions

6 months

•  in extreme operating conditions (frequent riding in rain, mud, snow)

as required

Full hub service (see Technical Manual at dtswiss.com)

•  Under normal operating conditions

12 months

•  in extreme operating conditions (frequent riding in rain, mud, snow)

as required

Check the hub for damage

before and after each ride

Clean with soft cloth and a suitable cleaner (see “Cleaning“ on page 4).
Do not use high pressure cleaners or aggressive cleaning agents!

after each ride

3.2  SAFETY

DANGER

DANGER TO LIFE DUE TO INCORRECT MAINTENANCE AND INCORRECT SPARE PARTS!

Unpredictable malfunctions can occur due to incorrect maintenance, incorrect installation or incorrect 

spare parts.

•  Maintenance may only be carried out by experienced specialists.

•  Use only original DT Swiss spare parts or spare parts approved by DT Swiss.

•  In cases of doubt, please contact a DT Swiss Service Center.

Содержание SPLINE WHEEL








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды