background image

14

[1]

Zone Definitions    Page 10

NOTE:

  When defining zones, assign delay zones first, then assign the other types.

Default

0 0

Zone 1

0 1

Zone 2

0 2

Zone 3

0 2

Zone 4

[2]

System Times    Page 11

Default

0 3 0

Entry Delay (seconds)

1 2 0

Exit Delay (seconds)

0 0 4

Bell Cut-off (minutes)

Valid entries are “001” to “255”; do not enter “000”.

[3]

Installer’s Code     Page 11

Default

0 5 1 0

[4]

Programmable Output Options (PGM1 and PGM2 Terminals)    Page 11

Enter two digits from the list below.  The first digit entered determines how PGM1 will operate; the second
digit entered determines how PGM2 will operate.

Default

1 3

Programmable Output

[1]

[

][7] activates PGM

[2]

Keypad sounder follow mode

[3]

Latched alarm

[4]

Steady Alarm / [P] Key

[5]

24-Hour Pulsed Alarm / [F] Key

[6]

PGM activates on  [A] Key alarm

[7]

PGM activates on Trouble alarm

[8]

PGM activates on any [F], [A] or [P] Key alarm

[9]

Arm / Disarm Status

[5]

1st System Option Code    Page 12

Default

Zone Light ON

Zone Light OFF

OFF

Zone Light 1

Momentary Keyswitch Arming Maintained Keyswitch Arming

ON

Zone Light 2

[P] Key silent

[P] Key audible

OFF

Zone Light 3

KEY Terminal: Tamper Zone

KEY Terminal: Keyswitch Operation

OFF

Zone Light 4

For Future Use

PROGRAMMING WORKSHEET

Digit 1

Digit 2

[0]

Slow / Audible

[0]

Standard Delay

[1]

Slow / Silent

[1]

Instant

[2]

Fast / Audible

[2]

Interior

[3]

Fast / Silent

[3]

Home-Away/Delay

[4]

24-Hour Steady Alarm

[5]

24-Hour Pulsed Alarm

Valid entries are from 1 to 9.

Do not enter 0.

Содержание PC51O





















Отзывы: