background image

9

PROGRAMMING GUIDE

With the system disarmed, enter [

][8][Installer’s Code].  The system can only be programmed while it is

disarmed.  The default Installer’s Code is [0510].  The Installer’s Code should be changed after the system is
installed; refer to Programming Section [3].

When the Installer’s Programming Command is entered, the “Armed” light will be ON and the “System” light will
FLASH to indicate that the system is ready for programming.  

NOTE: 

If no key entry is made for 2 minutes, the

system will return to the “Ready” mode and the Installer’s Programming Command will have to be entered again.

With the “Armed” light ON and the “System” light flashing, enter a digit from 1 to 5 to select a Section to program.
Note that each section is programmed independently.

Once the section to be programmed is entered, the keypad will beep 3 times; the “Ready” light will come ON,
the “Armed” light will be OFF, and the “System” light will FLASH.  The system is now ready to accept data for
the selected section.

To change the first digit in a section, enter a new digit from the keypad.  If you wish to keep the first digit
unchanged, enter the same number.  After entering the first digit, enter the second digit by pressing a number
on the keypad.

After entering the data, press the [#] Key to return to the programming mode.  You may then enter another
Section for programming.  For 2-digit numbers, both digits must be programmed before pressing the [#] Key.
Only the data entered before pressing the [#] Key will be changed.

When all data for a section is completely entered, the keypad sounder will beep several times to indicate that
all expected data has been entered.  When a section is completely programmed, enter the number of the next
section to be programmed.

Section [5]: Enabling System Functions

Section [5] allows you to enable or disable various system functions.  Refer to the Programming Worksheet to
see which features are represented by the Zone Lights.  Press the number key corresponding to the desired
feature to turn the Zone Light ON or OFF.  When all selections have been made, press the [#] Key to save the
changes and return to the program mode.

Resetting Programming to the Factory Default Settings

The system may be reset to its factory default programming by following this procedure:

1

Remove all power, AC and battery, from the PC510

2

Remove all wiring connections from the PGM1 and Zone 1 terminals

3

Connect the PGM1 and Zone 1 terminals together

4

Apply power to the PC510 and wait for 10 seconds

5

After approximately 10 seconds, the keypad sounder will beep and Zone Light 1 will come ON

6

Remove all power, AC and battery, from the PC510

7

Remove the connection between the PGM1 and Zone 1 terminals

8

Re-connect original wiring to the PGM1 and Zone 1 terminals

9

Restore power to the PC510; the Programming Sections have now been restored to the factory default

settings

Содержание PC51O





















Отзывы: