DSC LE2080 Скачать руководство пользователя страница 39

Страница: 39 / 60

[971] - EEPROM Map Version

[972] - Virtual Keypad Language Version

[976] - Radio Configuration File Version

[977] - Cellular Network Provider - MCC/MNC Code

[978] - Cellular Network Type

00 GPRS

04 LTE

01 EDGE

05 LTE Advanced 4G

02 WCDMA 3G

06 CDMA

03 HSDPA 3G

07 EVDO

[979] - Cellular Network CSQ

[980] - Radio Reset Codes

[981] - Radio Type

[982] - Radio Firmware Version

[983] - Firmware Update Diagnostics Section

Firmware updates for panel and the communicator itself can be made from the communicator.

Table 14: Response Code Descriptions and Corresponding Actions

Response

Code

Description of Response Code

Corresponding Action

Bad File

Version check failed

Contact DSC Tech Support, described the action
attempted with the system and supply them with the
Response Code in Section [983].

Image type mismatch

Device type mismatch

Hardware type mismatch

General variant mismatch

Firmware header wrong length

Panel is Busy

System update pending - panel is
armed

Disarm the panel to continue with system firmware
update process.

System update pending -AC trouble
(Any AC trouble; device/module)

Resolve the AC trouble to continue with system
firmware update process.

System update pending -low battery
(Any low battery trouble;
device/module)

Resolve the low battery trouble to continue with
system firmware update process.

System update pending -
communication in progress

Retry in a few minutes; if issue persists, contact DSC
Tech Support.

Firmware Update Sequence Change

System firmware update successful

None

System firmware update failure

At least one module was not updated. Use DLS to
reapply the firmware to the module not updated.

System firmware update failure -
module not found

At least one module was not responding during
firmware update. Ensure all modules enrolled are
physically connected and powered up.

Device firmware transfer begin

None

Device firmware module update
begin

None

Содержание LE2080





























































Результаты поиска

Содержание LE2080

Отзывы:

Похожие инструкции для LE2080

Бренды по названию

Популярные бренды

DSC LE2080, Руководство по установке

Результаты поиска

Содержание LE2080

Отзывы:

Похожие инструкции для LE2080

Бренды по названию

Популярные бренды