Dru Opera Deco-02, Инструкция по установке и эксплуатации

Страница: 18 / 24

USER MANUAL
Ignition
Ignition button A has three positions, i.e.:
O position button points to O
Pilot burner position button points to
Full position button points to
Turn the ignition button to the left from position O,
press down firmly as well and keep turning to the pilot
burner position . By turning the button, the pilot burner
is ignited by means of an electrical spark. When the pilot
burner burns, keep pressing down the button for approx.
10 sec. and then let go. The pilot burner is visible from
the side, behind the glass window. If the pilot burner
does not ignite at once, the above-mentioned action can
be repeated immediately by turning the pressed down
button back towards O and then left again towards the
pilot burner position. After letting go of the ignition
button, the pilot burner should continue to burn. Then
turn the ignition button further towards the full position
. Depending on thermostat button B, the main burner will
be ignited.
Controlling the temperature
The position of thermostat button B determines the
temperature in the room. Position 6 provides the highest
temperature, position 1 the lowest. The thermostat
controls the burner by modulating between “full position”
and “low position” of the burner. The thermostat will
automatically keep the room at the required set
temperature.
Switching off
Turn ignition button A back to the Pilot Burner position
( symbol), only the pilot burner will continue to burn.
In order to switch off the appliance fully, you must press
down button A and turn it back to position O.
Important
An incorporated safety lock will be activated if the
appliance is set to the ,,OFF” (O) position. Therefore, wait
5 minutes before re-igniting the appliance. Do not try
to press down the ignition button during this time, as it is
locked by means of the safety lock. Do not force the
button, because the mechanism could get damaged.
Eco control pack
It is possible to order a separately available “Eco control
pack” with remote control. The “Eco control pack” is
needed to get the best out of your appliance.
This set has a receiver that must be placed in the tray
specifically intended for this purpose.
The tray is located under the gas control and can be
reached by removing the cover.
Prevent cables from making contact with hot internal
components.
N.B.: If the flue spillage sensor is repeatedly
activated, a qualified gas installer should be
contacted.
USER INSTRUCTIONS
16
USER MANUAL
Ignition
Ignition button A has three positions, i.e.:
O position button points to O
Pilot burner position
button points to
Full position button points to
Turn the ignition button to the left from position O,
press down firmly as well and keep turning to the
pilot burner position . By turning the button, the
pilot burner is ignited by means of an electrical
spark. When the pilot burner burns, keep pressing
down the button for approx. 10 sec. and then let
go. The pilot burner is visible from the side, behind
the glass window. If the pilot burner does not
ignite at once, the above-mentioned action can be
repeated immediately by turning the pressed down
button back towards O and then left again towards
the pilot burner position. After letting go of the
ignition button, the pilot burner should continue to
burn. Then turn the ignition button further
towards the full position . Depending on
thermostat button B, the main burner will be
ignited.
Controlling the temperature
The position of thermostat button B determines
the temperature in the room. Position 6 provides
the highest temperature, position 1 the lowest.
The thermostat controls the burner by modulating
between “full position” and “low position” of the
burner. The thermostat will automatically keep the
room at the required set temperature.
Switching off
Turn ignition button A back to the Pilot Burner
position ( symbol), only the pilot burner will
continue to burn. In order to switch off the
appliance fully, you must press down button A and
turn it back to position O.
Important
An incorporated safety lock will be activated if the
appliance is set to the ,,OFF” (O) position.
Therefore, wait 5 minutes before re-igniting the
appliance. Do not try to press down the ignition
button during this time, as it is locked by means of
the safety lock. Do not force the button, because
the mechanism could get damaged.
Eco control pack
It is possible to order a separately available “Eco
control pack” with remote control. The “Eco
control pack” is needed to get the best out of your
appliance.
This set has a receiver that must be placed in the
tray specifically intended for this purpose.
Art 2-01: The tray is located on the left side of the
gas control.
Art 3-01, 4-01, 5-01, 6-01, 8-02, 10-02: The tray is
located under the gas control.
Prevent cables from making contact with hot
internal components.
1
6
2
3
4
5
A
B
38P-0744/0