Drive DeVilbiss Healthcare Theia, Инструкция по эксплуатации

Страница: 10 / 30

10
5. TRANSPORT AND STORAGE
5.1 Storage
• Detach the control unit from the support surface.
• Release CPR or rotate the CPR dial until it is open.
• Lay the mattress or cushion out flat and position upside down.
• Ensure there is no air trapped in the cells.
• Position the control unit on the mattress or cushion.
• The product should be rolled from the head end towards the foot end
(ensuring the control unit is fully covered).
• Place into storage bag/holdall to protect from dirt, debris, fluids etc.
• To prevent the risk of cross infection, when removing the system from
an end user’s residence ensure that all activities in relation to the
system are carried out using disposable gloves and that they are then
discarded appropriately, unless it can be verified that the cushion,
mattress and control unit have been suitably cleaned and disinfected
prior to collection.
• On the return of the system from an end users residence, prior to
putting into storage ensure it has been cleaned and disinfected in line
with the local infection control policy and/or as defined in section 10
of these instructions for use.
• Do not crease or stack mattresses, cushion and/or control units -
damage could be incurred.
• Do not store whilst inflated - damage could be incurred.
• Do not store objects such as side rails on top of the mattress or
cushion - damage could be incurred.
Warning
Caution
5.2 Transportation
Where possible, it is recommended the transport of mattresses should be
carried out on a flat based trolley or mattress trolley. Do not drag or pull the
mattress by its cover or foam core. Please follow local moving and handling
policies and guidelines when handling a mattress. It is recommended that two
people manoeuvre the mattress.
You can achieve 8 hours transport time by
carrying out the following procedure:
• Disconnect the umbilical cord from the
control unit by squeezing the two tabs and
pulling away (FIG 5).
• Seal using the cap marked ‘Transport’
(FIG 6).
• Switch off the control unit.
QUICK REFERENCE GUIDE P2 of 2
TO BE USED IN CONJUNCTION WITH THE FULL INSTRUCTIONS FOR USE FOR THIS
PRODUCT. THIS QUICK GUIDE DOES NOT REPLACE THE FULL DOCUMENT.
No. Symbol Description
1 LOW PRESSURE
NORMAL PRESSURE
MIN MAX
W
EI
GH
T
RA
NG
E
MID
MUTE STATIC
Weight Range Control: Turn dial
clockwise to increase mattress
pressure and anti-clockwise to
decrease mattress pressure. It
is recommended to adjust the
control to the max when first
inflated. Before changing the
control a clinical judgement is
required.
2
LOW PRESSURE
NORMAL PRESSURE
MIN MAX
W
EI
GH
T
RA
NG
E
MID
MUTE STATIC
Static Mode: Press to set the
air within the mattress to stay
static, green light will indicate
static mode is selected. The
system will not revert back to
alternating mode. The user must
press alternate button to return
to alternating mode.
Drive DeVilbiss Sidhil Ltd | APOLLO II | Quick Reference guide | REV 5
EROS
Pump with mattress options and cushion
LOW PRESSURE
NORMAL PRESSURE
MIN
MAX
W
EI
GH
T
RA
NG
E
MID
MUTE STATIC
3 2 1
No. Symbol
Description
3
LOW PRESSURE
NORMAL PRESSURE
MIN MAX
W
EI
GH
T
RA
NG
E
MID
MUTE STATIC
Alarm Mute: The audible alarm
will sound when the pressure
within the system is low or a
power failure is detected. To
mute, press the mute button and
to reactivate the alarm, re-press
the mute button.
LOW PRESSURE
NORMAL PRESSURE
MIN
MAX
W
EI
GH
T
RA
NG
E
MID
MUTE STATIC
Low Pressure : When abnormal
low pressure occurs, the low
pressure indicator will illuminate
and the alarm will be activated
to alert of a low pressure
condition.
Transport Mode
You can achieve 8 hours transport time by
carrying out the following procedure:
• Disconnect the umbilical cord from the power
unit by squeezing the two tabs and pulling
away
(FIG 5).
• Seal using the cap marked ‘Transport’
(FIG 6).
• Switch off the control unit.
1
1
2
FIG 5. FIG 6.