manualshive.com logo in svg

DriSteem Ultra-sorb LH, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
DriSteem Ultra-sorb LH Скачать руководство пользователя страница 8

Page 8 • DRI-STEEM Ultra-sorb Steam Dispersion Panel Installation, Operation, and Maintenance Manual

F i e l d   a s s e m b l y   o f   M o d e l   LV

STEP 2 -  Bolt the mounting flanges to the supply header  
assembly 
 

Refer to Figure 8-1 and 8-2. Attach the two mounting flanges 
as indicated using ¼" - 20 bolts with the nuts only finger tightened.

 

 
STEP 3 - Insert the dispersion tubes 
 

Refer to Figure 8-4. Insert the plain ends (no slip couplings) of 
the dispersion tubes into the slip coupling already mounted on the 
supply header assembly. The slip couplings are factory lubricated; 
if well aligned during insertion, no further lubrication should be 
needed. Push and twist the tube in until it bottoms out on the inter-
nal shoulder of the slip coupling. See Figure 8-3.  
 

C A U T I O N !

 Use care to avoid cutting the internal O-rings of the 

slip couplings.

OM-260-2

OM-260-3

¼" - 20 bolt

Washer and nut

Mounting     
      flange

Steam 
inlet

Steam 
inlet

Slip coupling 
with shoulder

Dispersion 
tube

Condensate 
drain tube

OM-238-6

Shoulder

O-rings

OM-239

¼" - 20 bolts

Mounting flange

Figure 8-1:
Supply header assembly

Figure 8-2:
Detail view of mounting flange

Figure 8-4:
Dispersion tubes

Figure 8-3:
Detail view of slip coupling

Supply header assembly

Supply header assembly

US-IOM-0108.pdf   8

4/21/2010   11:34:58 AM

Содержание Ultra-sorb LH





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды