manualshive.com logo in svg

DriSteem Ultra-sorb LH, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
DriSteem Ultra-sorb LH Скачать руководство пользователя страница 21

DRI-STEEM Ultra-sorb Steam Dispersion Panel Installation, Operation, and Maintenance Manual • Page 21

3.  Remove the dispersion tube. 

Make sure nothing loose falls 
into the header.

Installing High-efficiency tubes 

Note:

  The photos below show the High-efficiency tubes 

without the 

clear poly film

 for demonstration purposes only. To prevent 

dirty insulating material, install the High-efficiency tubes before 
tearing off the clear poly film.

Perform the following steps for each 
insulated tube being installed:

 1. Slide the new slip couplings onto the 

high-efficiency dispersion tube as 
shown.

2.  Push and twist the dispersion tube 

onto the supply header until the 
slip coupling shoulder bottoms out. 
Connect the dispersion tube to the 
condensate header with the other 
slip coupling.

3.  Push the shoulderless slip coupling 

against the stop disc on the 
condensate header.

4.  Rotate the dispersion tube to point 

the tubelets perpendicular to the 
airstream.

Step 3

Step 1

Slip coupling 
with shoulder; 
supply-header-
end of tube

Slip coupling  
without shoulder; 
condensate-header- 
end of tube

Step 2

Step 3

Step 4

R e t r o f i t t i n g   a n   e x i s t i n g   U l t r a - s o r b

Note:

 

See maintenance instructions for high-
efficiency tubes on Page 23.

US-IOM-0108.pdf   21

4/21/2010   11:34:59 AM

Содержание Ultra-sorb LH





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды