110489Q #110128 (F410), #110133 (F411)
8
Legend Brands, Inc.
clean the vertical (condenser) coil, contact Service for
instructions.
To reassemble, follow the above steps in reverse. Be
sure to reinstall heat exchange block in the original
orientation. When installing the rear cover, carefully
thread the pump hose through the hole in the back
pocket before putting the cover in place.
NOTICE
:
Rubber strips are attached to the outside
edges of the evaporator and condenser coils to
provide an airtight seal around the heat exchange
block. When reinstalling the block, make sure the
seals are in place and are not kinked or folded.
TROUBLESHOOTING
F A U L T
C A U S E
S O L U T I O N
Water drips out
when moving unit
Unit was unplugged before
purging was complete.
Purge unit before moving. See “At the End of the Job.”
Unit does not
operate
Unit not switched on.
No power to machine.
Switch unit on.
Plug in unit; check power cord connection at wall outlet and at
base of unit.
Unit operating,
but room not dry
Not enough time to dry.
Poor air movement in room.
Excessive moist air infiltration.
Make sure “Humidistat” is OFF.
Allow more time for drying.
Increase air movement with air movers.
Seal off area to reduce infiltration.
Unit collects too
little water
Room air is dry.
Room temperature is too low.
Filter is full.
Coils are clogged.
Make sure “Humidistat” is OFF.
Confirm humidity level with hygrometer.
Increase room temperature.
Check filter. Replace as necessary.
Check coils. Clean as necessary.
If the problem you are experiencing is not listed here, call your local distributor or contact
our Service Department at 800-932-3030 for further assistance.
SPECIFICATIONS
Model
LGR 2800i #110128
(F410)
LGR 3500i #110133
(F411)
Use weight
156 lbs. | 70.8 kg
158 lbs. | 71.2 kg
Dimensions
(H × D × W)
40.5 × 23 × 24 in.
103 × 58 × 61 cm
40.5 × 23 × 24 in.
103 × 58 × 61 cm
Power
8.0 amps,
120 volts
11.2 amps,
120 volts
Water removal
AHAM (80°F/60%
RH)
130 pts. | 61.5 liters /
day
170 pts. | 80.4 liters /
day
Water removal max.
(90°F/90% RH)
200 pts. | 94.6 liters /
day
240 pts. | 113.6 liters
/ day
Water removal
80°F/20% RH
20 pts. | 9.5 liters /
day
24 pts. | 11.4 liters /
day
Max process air
400 CFM | 679.7
CMH*
400 CFM | 679.7
CMH*
Operating range
33°F–125°F
1°C–52°C
33°F–100°F
1°C–38°C
Construction
Rotomolded shell
Rotomolded shell
Safety
ETL certified to CSA
22.2 no. 92
ETL certified to CSA
22.2 no. 92
Specifications are subject to change without notice. Some values may
be approximate. *Automatic variable speed for optimized
performance.
PARTS INCLUDED
40 ft. (12 m) of drain hose with quick-connect fitting.
25 ft. (7.6 m) detachable power cord.
4-PRO air filter. Reorder #121708 (F584) 24 pk.
ACCESSORIES
VMax Adaptor #100694 (F422)
Sto&Go Ducting #113260 (F405)
FOR PARTS AND SERVICE CALL YOUR LOCAL
DISTRIBUTOR
or Dri-Eaz at 800-932-3030.
Visit
warranty.LegendBrandsRestoration.com
your purchase to ensure you receive any important
product releases.
WARNING: This product may expose you to
chemicals, including lead and phthalates, known
to the State of California to cause cancer, birth defects,
or other reproductive harm. For more information, go to
P65Warnings.ca.gov
