Dreamline TETRA, Руководство по установке

Страница: 4 / 9

Rev.1.1 Page 4
Installation
1. Locate the Wall profile 1 (01) in the package. Refer to dimensions in fig. 1 to locate the
proper position for it according to the measurement. Outline the external position of the wall
profile.
Use predrilled holes in the aluminum profile to mark holes for drilling. Drill the holes
using drill bit 5/16” and push the
Wall Anchors (19) into the holes.
2. Run a bead of silicone along the wall profile length. Push the Pivot retainer (15) into the top
and bottom sides of the Wall profile 1. Place the Wall Profile 1 onto the threshold against the
marked line. Secure the Wall Profile 1 and the Pivot retainers (15) at the top and bottom
ends of the profile with Screws ST4.2×30 (26) . See Fig. 1 for details.
3.
Repeat Step 1 to attach the Wall profile 2 (04) to the wall (this wall profile will have no
pre-cut seat for pivot retainers).
Doesn’t require pivot retainers.
See Fig. 2 for details.
4.
Locate the short Glass profile 1 (2) . Push the upper Pivot bracket (17) into the top groove
of the Glass profile ; then secure it to the profile with Countersunk screws ST4.2×25 (24)
and M4×16 bolt (20) . Repeat the same steps for the bottom pivot bracket. See Fig 3 for
details.
5. Attach the bottom Pivot assembly (16) onto the Pivot bracket (17) . Make sure that the
Washer (18) is in between the pivot assembly and the pivot bracket. The washer may
already be placed on the pivot assembly pin or inside the pivot bracket. Repeat the same for
the top pivot assembly. The pivot assembly and the pivot bracket edges should be aligned.
The bolt side should face inward. Remove the back fastener from the pivot assembly. Set
the
Glass door (05) so the holes are aligned. Make sure the rubber gaskets are in between
the glass and the metal parts. Secure the glass with the back fastener using the provided
bolts. See fig. 4 for details.
6. Mount the Handle (07) on the glass door. See fig. 5 for details.
7. Push the assembled glass door into the groove of the Wall profile 1 . Secure the Upper
pivot bracket (17) and the Upper pivot retainer (15) with Hex Socket round head bolt
M6×12 (27) . See Fig. 6, 7 for details.
8. Apply silicone along the full length of the Glass profile 2 (03) channel and then push the
Return glass (06) into the channel. (Note that the hole in the return glass should be located
at the bottom and close to the glass door). Gently tap on the Glass profile 2 (03) with the
rubber hammer through the wooden block so the Return glass slides inside the Glass
profile 2 . See fig. 8 for details.
9. Push the Magnetic strips (9) on the edges of the return glass and the swing door, the
Anti-water strip (10)
– inside the glass profile channel
and the Bottom anti-water strip (11)
on the bottom of the door. Make sure the glass door is leveled and plumbed and then tighten
up the
Hex socket round head bolt M6×12 (27) . See Fig. 9 for details.
10. Adjust the positions of the glass door and the return glass to ensure that the door is closing
tightly. Drill the holes at the top, middle and bottom in the wall profile 1, and secure it to the
glass profile 1 with
Countersunk screws ST4.2×16 (23) and cover the exposed screw
heads with Decorative plugs (22) . See Fig. 10 for details.
11. Repeat Step 10 to attach the Wall profile 2 to glass profile 2. See Fig. 11 for details.
12. Place the Hex socket flat head bolt M6×12 (28) to the bottom Pivot bracket (17) or you
can drill through the screw hole, apply silicone and secure it using Countersunk screw
M4.2 ×25 (24). See Fig. 12 for details.
13. Attach the Bottom bracket (15) on the stationary glass and drill through the slotted hole of
the bracket. Screw the bracket to the threshold with the Round head screw ST4.2×25 (25)
and cover it with the Decorative cover (21) . See fig. 13 for details.
14. Find the Support bar (08) and attach the Support bar wall bracket (12) and Support bar
glass bracket (13) to the support bar. Loosen the glass holding set-screw on the Glass