Draper GT2222, Инструкция по эксплуатации

Страница: 7 / 10

36. Warning ! Danger of injury by the line cutting
device. After replacing a spool or lengthening
the cutting line, be sure to bring the unit
onto normal working position before turning it
on again.
37. Have a damaged cutting head replaced
immediately - even if it only has superficial
cracks. Never attempt to repair a damaged
cutting head.
38. Always switch off your trimmer and
disconnect it from the power supply before
taking a break and after finishing work. Do
not forget maintenance. (Plug disconnected!)
Only carry out maintenance and repairs
described in these operating instructions.
Any other work should be performed by
your dealer.
39. Inspect cooling air slots on the motor housing
at regular intervals for clog-ups and clean
as necessary.
40. Only use original spare parts.
41. Only use original cutting heads and
replacement spools. Never use metal cutting
devices.
42. Clean plastic parts with a damp cloth. Do
not use aggressive cleaning chemicals.
43. Never hose down the electric trimmer!
44. Store trimmer indoors in a dry, high or
locked place and always keep out of reach
of children.
Important notice - so your guarantee does not
expire:
• Always keep the air-intake clean.
• Never use a longer line than the blade-retainer
allows to use.
• Only use original monofilaments with 1,4 mm
ø and original spools.
• Never press the cutting head on the ground,
while motor is running.
• Never hit the cutting head on a hard
underground, otherwise you will unbalance
and damage the motor shaft.
5.
Connecting the trimmer
(fig. 1)
The machine can only be used on single-phase AC
current. It is double-insulated in accordance with
Class II VDE 0740 and EEC 20 and therefore, it can be
used from sockets without earth wire. Before using
the trimmer, ensure that the mains voltage is the
same as the operating voltage shown on the rating
plate.
Wires of extension cord must have the following
minimum cross sectional area:
up to 25 m (80 ft): 1 mm²
more than 25 m (80 ft): 1,5 mm²
• Make a loop in the extension cord, push it through
the opening in the handle and hook over the lug
(strain relief).
• After finishing work, unhook loop from lug and pull
it out of the handle.
6. Mounting the protection cover
(fig. 3+4)
Remove the spool cover by pushing the spool cover
tab (fig. 15, pos. 1) at the side of the cutting head
inwards. Remove the spool and the spring. Place
the protection cover onto the trimmer housing in
such a way that the 2 guide edges of the protection
cover are located in the corresponding gaps of the
motor housing. Now turn the protection cover by 90°
up to the right position as shown in the illustration.
The guide edges of the protection cover must be
placed properly in the corresponding groove of the
motor housing. Finally, fix the protection cover
with the enclosed screw. Insert spring and spool.
Thereafter, position spool cover and fix it on the
cutting head.
Attention: With model GT 3525 T and GRT 4729
DA the protection cover can be assembled without
removing the cutting head.
7. Switching on / off
(fig. 2)
To operate your grass trimmer:
• Make sure you have a secure footing.
• Hold the trimmer firmly (with both hands).
• Stand upright - hold trimmer in relaxed position.
• Do not rest the cutting head on the ground.
• Squeeze the switch.
• The trimmer is switched off when you release the
switch.
8. Cutting Angle and Height Adjustment
Height adjustment-(fig. 5): Press button 1 and
adjust length of shaft to the most comfortable of the
three positions. Press button 2 and adjust front
handle as required.
Cutting angle adjustment: Press button 3 to release
cutting head (fig. 6) - it can now be swivelled to two
other positions. Press button 1 and rotate handle
180 degrees as far as to the stop (ill 7). Position for
edging-(fig. 8)
9. Trimming Grass and Weeds
(fig. 9)
• Sweep trimmer back and forth uniformly to cut
small patches of grass or weeds. The trimmer is
not constructed and suitable for cutting large
areas.