background image

4

Safety-related information

en

1

Safety-related information

1.1

Basic safety information

Before using this product, carefully read the associated 
instructions for use. This document does not replace the 
instructions for use.

Incorrect calibration

An incorrect calibration leads to incorrect measured values.

The sensitivity must be checked daily before first using the 
device, with a known concentration of the gas to be 
measured that corresponds to 25 to 50 % of the final 
concentration. The accuracy must amount to 0 to +20 % of 
the actual value. The accuracy can be corrected by 
calibration.

1.2

Safety information on explosion 
protection

Devices or components that are used in potentially explosive 
atmospheres and which are tested and approved in 
accordance with national, European or international explosion 
protection guidelines may only be used under the approved 
conditions in compliance with the statutory provisions.

Oxygen-enriched atmospheres

Explosion protection is not guaranteed in oxygen-enriched 
atmospheres (>21 Vol% O

2

).

Remove the device from the potentially explosive 
atmosphere.

Risk of explosion!

Do not open the gas detector in explosion-hazard areas.

Specific application conditions

In certain extreme conditions, open plastic parts and non-
earthed metal parts of the housing may store a combustible 
level of electrostatic charge.

Activities such as carrying the device in a bag or attached 
to a belt, operating the button field or cleaning the device 
with a damp cloth do not represent a significant 
electrostatic danger. However, if a mechanism which 
generates static charge, such as repeated rubbing against 
clothing, is identified, suitable precautionary measures 
must be implemented, e.g. the use of anti-static clothing 
and anti-static footwear.

2

Conventions used in this 
document

2.1

Definition of alert icons

The following alert messages are used in this document to 
provide and highlight areas of the associated text that require 
a greater awareness by the user. A definition of the meaning of 
each alert message is as follows:

WARNING

Indicates a potentially hazardous situation. If not avoided, it 
could result in death or serious injury.

NOTICE

Indicates a potentially hazardous situation. If not avoided, it 
could result in damage to the product or environment.

2.2

Typographical conventions

This symbol identifies information that make the product 
easier to use.

2.3

Glossary

Technical term

Explanation

Operation signal

A periodic optical (green LED) and/or 
acoustic signal.

D-Light

The D-Light allows the user to check and 
indicate compliance with certain settings 
(e.g. bump test interval). The green LED 
flashes for a short period and 
superimposes the optical operation 
signal.

Содержание Pac 6000

























Отзывы: