background image

Introduction 

DESTACO CAMCO Index Drives are engineered and manufactured to very high tolerances which 
necessitate careful inspection and maintenance. This manual is a general guide to lubrication, 
troubleshooting and general information about index drives. 

In addition to this General Service Manual, DESTACO has other service manuals devoted to the 
specific model CAMCO index drive you are using. The model-specific service manuals cover 
disassembly and assembly of the major components. They also contain an exploded view drawing of 
the index drive with a complete bill of materials for identifying and ordering spare or replacement 
parts. 

Some users of index drives have the facilities and trained personnel to accomplish service repair. 
You must determine the extent to which intricate servicing should be done in your own facility. When 
in doubt, DESTACO recommends that DESTACO trained service technicians make the repairs. 

How to Use This Service Manual 

1.  This manual deals covers general service and maintenance subjects. In addition to this manual 

you should have the model-specific service manual. You may request a copy from your local 
DESTACO Sales Representative, directly from DESTACO CAMCO Products (847-459-5200 / 
[email protected]) or download a copy from destaco.com. 

2.  The Model Number Interpretation section will assist you in identifying the model you have and the 

characteristics of your index drive 

3.  The Troubleshooting Guide will help you diagnose potential problems. 

4.  This manual will explain how to order parts or return an Index Drive to DESTACO for repair. 

IMPORTANT: 

The Bill of Materials listed in the model-specific service manual is for a standard 

unit. If you feel you have a special unit, or are in doubt, please use the procedures outlined in the 
“How to Order Parts” section. 

5. Read 

all 

CAUTIONS

 and 

WARNINGS

 prior to service or repair. 

6. Read 

WARRANTY

 prior to service or repair. 

Warranty 

DESTACO products are warranted for one (1) year from the date of shipment to be free from defects 
in workmanship and materials 

The foregoing warranty is exclusive and in lieu of all other warranties, whether written or orally 
expressed or implied and there are no warranties of merchantability or fitness for particular use. 

DESTACO’s obligation under the foregoing is limited to replace free of charge, including the lowest 
transportation cost, but not including installation or any other charges, any part that our inspection 
shows to be defective provided that the part was properly installed, suitably maintained and not 
subject to misuse or abuse, and further provided that the defective parts are returned to our plant 
within one (1) year after delivery by us. Written permission for such return must first be obtained from 
DESTACO. A complete explanation is required of the alleged defects and circumstances.  

See the "How to Return for Repair" section of this manual. 

Содержание DESTACO CAMCO 1100RNG





























Отзывы: