background image

1.1 Principle of operation

The male screw and the female screw mesh and rotate
in opposite directions inside the casing fitted with inlet
and discharge ports.

Rotation generates a volume increase on the inner face
between threads and grooves, which corresponds to
inlet, and a volume reduction on the upper face, which
corresponds to compression.

On the discharge port side, a set of gears synchronizes
the male screw and the female screw. Thus, the screws
are not in contact. The discharged air does not enter in
contact with any friction part and remains clean and free
from particles.

On the drive shaft side, the female screw is driven by a
set of step-up gears.

An oil pump delivers pressurized oil which circulates,
lubricating gears and ball bearings.

Sealing is provided between lubricated parts and the
compression stage by means of labyrinth seals. These
seals do not enter in contact with the shaft and are not
subject to wear.

Thanks to its technology, TYPHON compressor is relia-
ble and has a long service life.

TYPHON compressor needs very limited maintenance,
which reduces vehicle downtime.

TYPHON version 2C drive speed (2000 rpm) was defi-
ned so as to drive it directly through universal joints from
a P.T.O shaft.

Our compressors are delivered without oil. The use of
a compressor with an oil level that is not located bet-
ween the two limits indicated by the gauge can lead
to important property damage and serious injuries.

TYPHON 1000 INTERCOOLER package includes the follo-
wing accessories :

• Inlet filter
• Silencer
• Check and relief valve
• Chair and pulley driving system
• Electrically propeller cooling fan
• Heat exchanger
• Filter clogging gauge

TYPHON 1000 COVER package includes the following
accessories :

• Inlet filter
• Silencer
• Check and relief valve
• Chair and pulley driving system
• Filter clogging gauge

This package is similar to the INTERCOOLER package with-
out the air cooling function.

Cooler

Outlet

port

Inlet filter

Oil gauge

Chair

Pulley

Compressor

4/21

NT 1401-F00 12.05 Cold front outlet Intercooler TYPHON e

11..  G

GE

EN

NE

ER

RA

ALL  D

DA

AT

TA

A

Содержание Blackmer TYPHON 1000






















Отзывы: