Doosan AD158TI Скачать руководство пользователя страница 272

Страница: 272 / 294

HY-DP-MANUAL-001 19

No.

Alarm

Action Feature

①

Coolant temperature (WATER TEMP)

•

Alarm (buzzer) will be activated when the

temperature is

93℃

or higher

②

Engine oil pressure (ENGINE OIL PRESS)

•

Alarm (buzzer) will be activated on when

the pressure is

1 bar

or lower

③

Gearbox oil pressure (GEARBOX OIL PRESS)

•

Alarm (buzzer) will be activated when the

pressure is

1 bar

or lower

④

Charging (CHARGE)

•

Alarm (buzzer) will be activated when the

battery voltage is lower than 27V

⑤

Coolant level (WATER LEVEL)

•

Alarm (buzzer) will be activated when the

level is

30%

or lower.

⑥

Fuel leakage (FUEL LEAKAGE)

•

Alarm (buzzer) will be activated when oil

leak occurs (default setting is ‘disabled’)

⑦

Engine over speed (OVER SPEED)

•

Alarm (buzzer) will be activated when the

speed exceeds

115%

of the rate speed

3.8.8

Engine Alarm

The alarm will be activated with buzzer beeping when problems for coolant temperature, engine oil
pressure, gearbox oil pressure, charging, coolant level, fuel leakage and over speed are detected.

①

[Fig. 3-24] Engine Alarm

3.8.9

Engine Stop

When the over speed exceeds

120%

of the rate speed

→

Enable/Disable engine stop

When the coolant temperature exceeds

103℃

→

Enable/Disable engine stop

When the oil pressure is

0.5bar

or lower

→

Enable/Disable engine stop

When fuel leakage occurs

→

Enable/Disable engine stop

When the coolant level is

15%

or lower

→

Enable/Disable engine stop

Stop Valve: the stop button will be activated by users (when the engine continues at

RPM for 7 seconds)

3. Part Names, Operation and Settings

[Table 3-10] Alarm Features

②

③

④

⑤

⑥

⑦

※ How to deactivate the engine alarm

- Press SYSTEM RESET button on the right for 3 seconds, the system will reboot and the alarm

will be deactivated (rebooting is available while the ship navigates without causing problems).

Содержание AD158TI







































































































































































































































































































Результаты поиска

Содержание AD158TI

Отзывы:

Бренды по названию

Популярные бренды

Doosan AD158TI, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание AD158TI

Отзывы:

Бренды по названию

Популярные бренды