Doosan AD158TI Скачать руководство пользователя страница 197

Страница: 197 / 294

- 9 -

Description of Controller Terminology

1. Starting Fuel

Controls the amount of starting fuel during the initial ignition. When rotated clockwise, the amount of fuel
increases.

2. Speed Ramping

Controls the time required to reach the maximum rpm. When rotated counterclockwise, the time required
for reaching the rated rpm decreases.

3. Idle

Adjusts the idle rpm of the equipment. When rotated clockwise, the engine rpm increases.

4. Gain

Stabilizes fluctuations in speed occurring in the engine.

5. Stability

Stabilizes fluctuations in speed caused by the engine load.

6. Speed

Adjusts the engine rpm. When rotated clockwise, the engine rpm rises.

7. Overspeed

Adjusts the engine overspeed rpm. When rotated clockwise, the maximum rpm rises.

8. Droop rpm

Used when running the generator in parallel.

9. Reset

Used when resetting the overspeed controller.

10. Test

Used when checking or setting the overspeed.

11. Terminals A and B

Connected to the actuator in the engine injection pump. (No polarity)

12. Terminals C and D

Connected (no polarity) to the magnetic pick-up sensor.
Shielded wire must be used. It must also not be connected to the magnetic pick-up sensor for any other
purposes.

13. Terminals E and F

Connected to the battery (E R - terminal, F R + terminal).

14. Terminals G and M

Terminals for maintaining the idle rpm.

15. Terminals K and L

Terminals for droop.

16. Terminals H, J, N and P

Auxiliary terminals.

Содержание AD158TI







































































































































































































































































































Результаты поиска

Содержание AD158TI

Отзывы:

Бренды по названию

Популярные бренды

Doosan AD158TI, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание AD158TI

Отзывы:

Бренды по названию

Популярные бренды