Donaldson Torit Dalamatic DLMV 10/10 Скачать руководство пользователя страница 6

3

Donaldson Company, Inc.

During normal operation, dust-laden air is drawn to the 

filter bags. The velocity is reduced and natural pre-

separation, caused by the effects of gravity, takes place. 

Fine particles collect on the outside surface of the filter 

bag and clean, filtered air passes to the center of the bag 

and discharges through the clean-air outlet.

Filter cleaning is completed using pulse-jet technology. A 

jet tube positioned over each filter bag distributes a pulse 

of compressed air through the filter. As the compressed 

air enters the filter bag, airflow is temporarily reversed 

and the bag inflates dislodging the dust cake formed on 

the outside of the bag. The bag deflates and the dust 

cake falls back into the silo or process equipment.

jet tube

outlet header

seal frame

sealing flange

and ring

accumulated

dust cake

wire insert

filter bag

clean-air plenum

dirty-air plenum

jet tube injecting

compressed air

air inducted by

force of jet
clean-air plenum

dirty-air plenum

airflow temporarily

reversed, inflating bag

and dislodging

dust cake

dust cake falls

back into the silo

or process equipment

Normal Operation

Filter Cleaning Operation

clean-air outlet

Unit Operation

Operation

Содержание Dalamatic DLMV 10/10

































Отзывы: