Donaldson Torit Dalamatic DLMV 10/10 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 32

Donaldson Torit Dalamatic DLMV 10/10 Скачать руководство пользователя страница 22

19

Donaldson Company, Inc.

clean air plenum

pressure tap location

1/8-in NPT male

adapter

NPT male adapter

static pressure tee

dirty air plenum pressure

tap location

1/8-in NPT male adapter

plastic tubing

two 1/8-in NPT adapters

low-pressure port

high-pressure port

Photohelic gauge

Photohelic Gauge, Remote Panel or Door Installation

4. Thirty-five feet of plastic tubing is supplied and must

be cut in two sections. Connect one section of tubing

from the gauge’s high-pressure port to the pressure

fitting located in the dirty-air plenum. Connect

remaining tubing from the gauge’s low-pressure

port to the fitting in the clean-air plenum. Additional

tubing can be ordered from your representative.

5. Zero and maintain the gauge as directed in the

manufacturer’s Operating and Maintenance

Instructions provided.

6. To install the Photohelic Gauge mounted in a NEMA

4, Weatherproof Enclosure, follow Steps 4 and 5.

«
...
20
21
22
23
24
...
»

Содержание Dalamatic DLMV 10/10

































Отзывы:

Нет отзывов