DOMUSA Evolution EV AC Скачать руководство пользователя страница 28

Страница: 28 / 40

Evolution EV AC

ALARM CODES

The

Evolution EV AC

boiler has an electronic circuit which performs continuous self-testing to detect

any operating failures in the boiler. When the electronic control detects an operating error, it indicates

this by showing an alarm code on the display. The following list describes the possible alarm codes:

CODE

ALARM

DESCRIPTION

AL AP

bar

ºC

Pressure.

The pressure in the installation has dropped to below

0.5 bar. The boiler will cut out. To unblock it, fill the

installation at a pressure of 1 - 1.5 bar.

This alarm may be set off due to the water having

been drained from the boiler or due to leakage in the

installation.

If this alarm occurs repeatedly, you should contact the

nearest official technical assistance service.

AL AT

bar

ºC

Temperature.

The boiler has exceeded the safety temperature of 110

ºC. The boiler will cut out. To unblock it, press the

Safety Thermostat button when the temperature has

dropped.

If this alarm occurs repeatedly, you should contact the

nearest official technical assistance service.

AL AQ

bar

ºC

Burner.

The burner has cut out. To unblock it, press the
illuminated button on the burner

(2)

This alarm is set off when there is a functioning

anomaly in the burner or the fuel installation.

If this alarm occurs repeatedly, you should contact the

nearest official technical assistance service.

AL S1

bar

ºC

Boiler sensor.

The boiler sensor

(4)

is defective or disconnected.

ontact your nearest official technical assistance

service to have it replaced.

AL S2

bar

ºC

Hot water sensor

(with storage heater

only)

The storage heater hot water sensor is defective or
disconnected.

ontact your nearest official technical

assistance service to have it replaced.

AL S3

bar

ºC

Flow sensor SRAC2/EV.
(only with kit SRAC2/EV).

The underfloor heating sensor is defective or
disconnected.

ontact your nearest official technical

assistance service to have it replaced.

AL S4

bar

ºC

Pressure sensor

The pressure sensor

(5)

is defective or disconnected.

ontact your nearest official technical assistance

service to have it replaced.

NOTE:

It will be very useful for the technical assistance service if you can inform them of the alarm

code that has appeared.

Содержание Evolution EV AC









































Результаты поиска

Содержание Evolution EV AC

Отзывы:

Похожие инструкции для Evolution EV AC

Бренды по названию

Популярные бренды

DOMUSA Evolution EV AC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Evolution EV AC

Отзывы:

Похожие инструкции для Evolution EV AC

Бренды по названию

Популярные бренды