background image

17.

THERMOELECTRIC 

 FAILURE SAFETY DEVICE (see fig, 58)

All

A l l

models equipped with an automatic failure device.

S

Fig. 58

gas operated or combined gas/electric refrigerator models dealt with in this

service instruction are equipped with an automatic failure device.

 purpose of incorporating an automatic flame failure device in the burner assem-

bly is to prevent unburned gas to escape from the burner and to avoid a fire hazard,

if, for some reason or other, the flame has been extinguished or blown out,

The safety device consists of the following parts:

1.

2.

3.

6.

7.

8.

9.

Spring loaded push button

Gas valve

Housing

Sensing clement with the hot junction of the

thermocoup   (Feeler)

Enamel insulated copper thread

Electromagnet

Outer tube

Armature

Spring

The 

 safety device functions as follows:

By pressing the push button (1) the gas valve (2) is opened and the gas can pass 

housing (3) on to the 

At the burner the feeler (4) is located. When the gas

flame of the burner is lit, some heat is transferred to the feeler 

 The hot

junction of the thermocouple is thus heated and an electric current is g e n e r a t e d .

This current passes through the copper wire (5) to the electromagnet (6) and back

through the outer tube (7). As soon as the electric current is generated, the

electromagnet attracts the armature (8) with the valve 

 The push button can 

be released,

As long as current is flowing, the 

 

 kept open and allows gas to pass co 

burner.

When the flame is extinguished, the heat transfer to the hot junction is 
and no electric current is generated.

 armature (8) with the valve (2) is 

forced back by the spring (9) and the gas flow through the valve (2) is  c l o s e d .

Important: 

 lighting the burner the push button (1) should be pressed f 

 

held in that position about 10 seconds, otherwise the gas may not get 

the burner properly,

Содержание RM24A





















































Отзывы: