Dodge 2012 Grand Caravan Скачать руководство пользователя страница 694 | Manualshive

Страница: 694 / 695

background image

INSTALLATION OF RADIO TRANSM ITTING EQUIPM ENT

Special design considerations are incorporated into this vehi-
cle’s electronic system to provide immunity to radio frequency
signals. Mobile two-way radios and telephone equipment must
be installed properly by trained personnel. The following must
be observed during installation.

The positive power connection should be made directly to the
battery and fused as close to the battery as possible. The
negative power connection should be made to body sheet metal
adjacent to the negative battery connection. This connection
should not be fused.

Antennas for two-way radios should be mounted on the roof or
the rear area of the vehicle. Care should be used in mounting
antennas with magnet bases. Magnets may affect the accuracy
or operation of the compass on vehicles so equipped.

The antenna cable should be as short as practical and routed
away from the vehicle wiring when possible. Use only fully
shielded coaxial cable.

Carefully match the antenna and cable to the radio to ensure a
low Standing Wave Ratio ( SWR) .

Mobile radio equipment with output power greater than normal
may require special precautions.

All installations should be checked for possible interference
between the communications equipment and the vehicle’s
electronic systems.

«
...
692
693
694
695
»

Содержание 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Grand Caravan

Бренд: Lancia Страницы: 276

Бренд: T-Tech Страницы: 38

Бренд: iDataLink Страницы: 30

Бренд: Aries Страницы: 3

Бренд: Yakima Страницы: 12

Бренд: Raytel LLC Страницы: 40

Бренд: PEUGEOT Страницы: 249

DLD Wide Range II

Бренд: VDO Страницы: 84

TravelCharge Companion GO-Plus

Бренд: Wagan Страницы: 3

Бренд: ULTIMATE SPEED Страницы: 32

Бренд: Chevrolet Страницы: 441

Бренд: Oypla Leisure Страницы: 4

Бренд: cam Страницы: 6

Бренд: r.LiNK Страницы: 21

Бренд: Acura Страницы: 4

Бренд: STO N SHO Страницы: 7

Бренд: Curtis Страницы: 5

Бренд: Makita Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды