Dodge 2012 Grand Caravan Скачать руководство пользователя страница 592 | Manualshive

Страница: 592 / 695

background image

4. Refer to “Torque Specifications” in this section for

proper wheel lug nut torque.

5. After 25 miles (40 km) check the lug nut torque with a

torque wrench to ensure that all lug nuts are properly
seated against the wheel.

JUMP-STARTING

If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.

Preparations For Jump-Start

The battery in your vehicle is located on the left side of
the engine compartment.

590

WHAT TO DO IN EMERGENCIES

«
...
590
591
592
593
594
...
»

Содержание 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Grand Caravan

Бренд: AA Products Страницы: 6

Бренд: AA Products Страницы: 8

Бренд: Hama Страницы: 2

Бренд: Ford Страницы: 2

Бренд: Edelbrock Страницы: 1

Бренд: FORM FIT Страницы: 2

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

Бренд: muth Страницы: 10

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: Cadillac Страницы: 20

Бренд: Van Guard Страницы: 3

Бренд: CTEK Страницы: 84

Бренд: Yakima Страницы: 9

Бренд: Subaru Страницы: 298

FXX ATM Emulator

Бренд: BMW Страницы: 5

1953 Traction Avant

Бренд: CITROEN Страницы: 26

Бренд: v.link Страницы: 19

Бренд: Pogo Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды