Dodge 2012 Grand Caravan Скачать руководство пользователя страница 462 | Manualshive

Страница: 462 / 695

background image

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.

The engine block heater cord is routed under the hood on
the driver’s side of the vehicle. It has a removable cap
that is located on the driver side of the Integrated Power
Module.

WARNING!

Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.

AUTOMATIC TRANSMISSION

CAUTION!

Damage to the transmission may occur if the follow-
ing precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the vehicle
has come to a complete stop and the engine is at
idle speed.

•

Do not shift between PARK, REVERSE, NEU-
TRAL, or DRIVE when the engine is above idle
speed.

•

Before shifting into any gear, make sure your foot
is firmly pressing the brake pedal.

NOTE:

You must press and hold the brake pedal while

shifting out of PARK.

460

STARTING AND OPERATING

«
...
460
461
462
463
464
...
»

Содержание 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Grand Caravan

Бренд: ZAPTEC Страницы: 240

Бренд: Jeep Страницы: 608

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Honda Страницы: 73

SmartShot Automatic 12V 1.5 Amp 5 Stage

Бренд: Yuasa Страницы: 44

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Rago FABRICATION Страницы: 10

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: Cadillac Страницы: 407

Бренд: Porsche Страницы: 313

Бренд: Saab Страницы: 12

Бренд: Ecco Страницы: 24

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: THIEYE Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды