Dodge 2012 Grand Caravan Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 695

background image

To Turn Off The Engine While In Remote Start
Mode

Press and release the REMOTE START button 1 time or
allow the engine to run for the entire 15 minute cycle.

NOTE:

To avoid unintentional shutdowns while in the

Remote Start Mode, the system will not allow the Remote
Start button to shut down the engine for 2 seconds after
receiving a valid Remote Start request.

When To Reset Remote Start

The vehicle can be started remotely up to a maximum of
two times. The vehicle is also allowed a maximum of one
failed start, where the Remote Starting sequence was
initiated but the engine stopped cranking without start-
ing. After either of these conditions, or if the Vehicle

Security Alarm system is alarming, or if the PANIC
button was pressed, the vehicle must be reset. Insert the
Key Fob into the ignition switch and turn the switch to
the ON/RUN position.

DOOR LOCKS

Manual Door Locks

Lock the front doors by pushing down on the lock knobs
on each door trim panel.

If the lock knob is down when you shut either front door,
the door will lock. Make sure the keys are not inside the
vehicle before closing the door.

34

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
34
35
36
37
38
...
»

Содержание 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Grand Caravan

Бренд: Pacbrake Страницы: 9

Бренд: GMC Страницы: 20

Бренд: Hama Страницы: 40

Бренд: Sears Страницы: 41

Бренд: BMW Страницы: 189

BEDXTENDER HD MAX 74841-00A

Бренд: AMP Research Страницы: 9

Бренд: Belkin Страницы: 2

GMC Yukon Denali 2005

Бренд: Cadillac Страницы: 456

Бренд: Saab Страницы: 63

Бренд: R&G Страницы: 20

Бренд: Whispbar Страницы: 70

Бренд: Honda Страницы: 124

Бренд: TOP VEHICLE TECH Страницы: 8

Бренд: ideus Страницы: 116

Бренд: Mazda Страницы: 7

Бренд: Ford Страницы: 17

Бренд: Scion Страницы: 24

Бренд: Mercedes-Benz Страницы: 356

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды