doble TDR9000 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 454

doble TDR9000 Скачать руководство пользователя страница 156

Configuring Test Plans

4-58

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Clicking these buttons:

Displays the first window of the testing sequence.
Refer to ”Running Tests” on page 4-75.

Displays a window, comprised of three tabs, where
the command parameters, including the triggers,
for that test type are configured or reconfigured
from an original Library Test Plan or Breaker Test
Plan. A complete description of command
parameters is given in

™ TRXField™

Software and Test Plan Dynamics” on page A-28.

These three tabs include:

• XXX Parameters

(

XXX

is the test being run) –

Refer to ”Parameters Tab”.

•

Trigger Input

– Refer to page 4-64.

•

Trigger Output

– Refer to page 4-66.

The

Trip Parameters

window (Figure 4.37) is used to explain

functionality. The Trigger Input and Trigger Output windows are the same
regardless of test type. Additional parameters for the Close test are listed
in Table 4.4 on page 4-61. Table 4.5 on page 4-62 lists the general
command parameters from the

XXX Parameters

tab that are available by

test type.

Configuring the
Command
Parameters

Configuring the command parameters for a test depends on the test type.
The Command Parameters window can be accessed in one of two ways:

• Click the

XXX Parameters

button.

or

• Click either the

Trigger In

or

Trigger Out

System module Virtual

Front Panel connectors, as shown in Figure 4.35.

Figure 4.35 Virtual Front Panel Trigger Connectors

«
...
154
155
156
157
158
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов