doble TDR9000 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 454

doble TDR9000 Скачать руководство пользователя страница 160

Configuring Test Plans

4-62

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

The Reclose, Trip Free and O-C-O versions of this
window have a scrollable picklist, which contains
the Standing, Delay, and Contact 1 test choices.
Each of these choices activates the Trip, Close, and
Delay 1 and 2 fields as listed in Table 4.5.

J

A

Recording Length

field where a recording length

is selected from a picklist. Each recording length
has a sampling rate associated with it. When a
length is selected, the sampling rate appears on the
window next to the picklist. Table 4.6 lists the
Recording Lengths and their associated sampling
rates.

Table 4.5 Command Parameters

Test Type

Command Parameters

Reclose (O-C)

Standing

Trip Command

Delay

Trip Command
Delay 1

Trip Free (C-O)

Standing

Close Command

Delay

Close Command
Delay 1

Contact 1 Make

Close Command

O-C-O

Standing

Trip Command
Close Command
Delay 2

Delay

Trip Command
Close Command
Delay 1
Delay 2

Contact 1 Make

Trip Command
Close Command
Delay 1

«
...
158
159
160
161
162
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов