manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 164 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 164

Configuring Test Plans

4-66

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

When 

OK

 is clicked on the 

Parameters

 window, the 

TDR9000

 tab 

reappears with a 

T

 icon displayed, as shown in Figure 4.39. This icon 

indicates that a trigger is configured.

Figure 4.39  Trigger Indicator

N

OTE

Once any external trigger is configured, all fields on the Parameters tab 
except the Recording Length are disabled and it appears as shown in 
Figure 4.40.

Figure 4.40  Trigger In Activated

Trigger Output

Tab

Trigger outputs may be configured for all tests, except Continuity, 
Self-Diag., Capacitance and Slow Close, using the 

Trigger Output 

tab 

(Figure 4.41) for the test being run. When this tab is selected, the 

Trigger 

State

 is set to 

Off

, which deactivates the output triggers from the Virtual 

Front Panel. This also occurs when the 

Trigger In

 is set to 

Aux Contact

 

(Figure 4.42).

Trigger
Indicator

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов