dji Naza Скачать руководство пользователя страница 4

Страница: 4 / 43

In The Box

Main Controller (MC)

The Main Controller (MC) is the brain of the system, it communicates

with all ESCs and RC transmitter to carry out the autopilot functionality.

It has a built-in Inertial Measurement Unit (IMU) consists of one 3-axis

accelerometer, one 3-axis gyroscope and a barometer for sensing the

attitude and altitude.

Versatile Unit (VU) ×

Specially desig

ned for Naza. It solves the high power consumption

problem of multi-rotor system, supply and monitor power for Naza and

other electronic devices. It also has an LED to indicate different

operating states of Naza and a USB interface for configuring the Naza

unit and firmware upgrade.

Optional

GPS & Compass Module

The GPS/Compass module is for sensing the position and direction.

Optional

GPS Bracket

Because the GPS & Compass are sensitive to magnetic interference, you should use this bracket to mount

the GPS module.

USB Cable

This cable is used to configure MC and

upgrade

firmware.

3-PIN Servo Cable

Cables used to connect the MC and the receiver.

3M Gummed Paper

Used for fixing Naza components on multi-

rotor’s frame.

Содержание Naza











































Результаты поиска

Содержание Naza

Отзывы:

dji Naza, Руководство пользователя, Страница: 4 / 43

Результаты поиска

Содержание Naza

Отзывы: