manualshive.com logo in svg

Dixon RZL-400, Руководство по эксплуатации и техническому обслуживанию, Страница: 54 / 78

Поделиться
Скачать
Dixon RZL-400 Скачать руководство пользователя страница 54

54

Rotary Lobe Pumps - RZL-400 Series

800.789.1718

Maintenance

Gearbox Disassembly

1.

  Remove the oil drain plug and drain the oil.

2.

  Remove the gear box cover bolts (6) from the rear cover (4).

3.

  Pull the rear cover off the drive shaft extension. If the cover is stuck use a soft hammer carefully to loosen it. 

4.

  Remove the rear cover oil seal (11) from the rear cover.

5.

  Remove the paper gasket (26) from the rear cover or gear box.

6.

   Straighten the locking tab of the bearing lock washer (12). Reinstall the rotors (38) on the drive (8) and idle (9) shafts. Lock the 

rotor with a plastic dowel. Remove the lock nut (12-1) and lock nut washer from the drive shaft (8) and idle shaft (9).

7.

  Pull the two helical-gears (14) off the pump shafts. Remove the gear keys (7).

8.

  Remove the front bearing gland set bolts (23).

9.

  Place the gearbox (1), wet end (rotor side) down, on an arbor press.

10.

  Protect the shaft ends with a wood block and press the drive and idle shaft out of the gearbox.

11.

  Remove the bearings (17) and spacers (18) together by pressing them out from the shafts.

12.

  Or remove bearings by puller.

13.

  The taper roller bearings for 400 series must be keep together with in-outside spacer and separated for drive and idle shafts.

Содержание RZL-400















































































Отзывы:

Нет отзывов