Dixon RZL-400 Скачать руководство пользователя страница 50

Страница: 50 / 78

Rotary Lobe Pumps - RZL-400 Series

800.789.1718

Maintenance

Rotor Clearance

Use feeler gauges to verify the back and radial clearances between the rotors and the housing. A depth gauge should be

used to verify the front clearance.

Rotor clearance must be precisely maintained to provide maximum pumping efficiency, prevent contact between rotors, rotor housing

and front cover during operation. If pumping efficiency is below expectations or if parts contact has occurred during operation (within

rated differential pressure) check rotor clearances and adjust if incorrect.

Standard Rotor Clearances (mm/in)

Model

Back Face

Front Face

Radial Sides

Radial Top &

Bottom

Rotor to

Rotor

RZL 105

0.05/0.002

0.07/0.003

0.1/0.004

RZL 110

0.05/0.002

0.07/0.003

0.1/0.004

RZL 115

0.15/0.006

0.27/0.011

0.12/0.005

0.15/0.006

RZL 120

0.15/0.006

0.3/0.012

0.15/0.006

RZL 220

0.2/0.008

0.3/0.012

0.15/0.006

0.2/0.008

RZL 225

0.2/0.008

0.4/0.016

0.2/0.008

RZL 330

0.3/0.012

0.4/0.016

0.2/0.008

0.3/0.012

RZL 340

0.3/0.012

0.5/0.020

0.3/0.012

RZL 440

0.45/0.018

0.55/0.022

0.3/0.012

0.4/0.016

RZL 450

0.45/0.018

0.7/0.028

0.45/0.018

0.4/0.016

There are two areas of rotor clearances as illustrated following:

•

Rotor tip clearance – not adjustable set by manufacturer

•

Front and back face clearance – adjustable by shim

Figure 20

Shims

Rotor to Housing

Back

Face

Front

Face

Radial Top & Bottom

Rotor to Rotor

Radial Sides

Содержание RZL-400















































































Результаты поиска

Содержание RZL-400

Отзывы:

Dixon RZL-400, Руководство по эксплуатации и техническому обслуживанию, Страница: 50 / 78

Результаты поиска

Содержание RZL-400

Отзывы: