manualshive.com logo in svg

Dixon RZL-400, Руководство по эксплуатации и техническому обслуживанию, Страница: 17 / 78

Поделиться
Скачать
Dixon RZL-400 Скачать руководство пользователя страница 17

17

Rotary Lobe Pumps - RZL-400 Series

800.789.1718

Tools Needed

• 

Rotor tool

• 

Plastic dowel

• 

Open ended wrench set

• 

Rubber mallet

• 

Flat head screw driver

• 

Feeler gauges

• 

Hex keys

• 

O-ring pick

• 

Spanner wrench

• 

Rotor extraction tool (optional)

Additional tools needed when assembling or disassembling gear box

  •  

Spanner wrench

  •  

Arbor press or bearing puller

Maintenance

Pump Housing Disassembly - Single Mechanical Seal

Prior to removal of pump, the shut-off valves in the suction and discharge lines must be closed.  If there is any risk that product 

may harden, crystallize or freeze in the pump it should be thoroughly drained and cleaned immediately after use. Same 

attention applies if there is a seal flush option. Power needs to be locked out to prevent unintended start of the pump.

Note:  Reference numbers are listed in the sectional view located on pages 61-73.

1.

  Loosen and remove the four hex nuts (33) from the front cover.

Содержание RZL-400















































































Отзывы:

Нет отзывов